background image

4

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

ASSEMBLY

Ensure the press and its components suffered no damage during transit. 
Should any damage be apparent, please contact your CLARKE dealer 
immediately.

IMPORTANT: Due to the weight of the press, we recommend that you get 
assistance from another person during assembly. 

1. With the main frame upright and adequately supported, bolt on the two 

feet using the nuts and bolts supplied.

IMPORTANT: We strongly recommend that the press be firmly secured to a 
firm and level floor using expansion bolts (not supplied).

2. Remove the plug on the front of the pump body and replace it with the 

vent plug supplied.

3. Remove the cap on top of the ram. Seal the thread with PTFE tape and 

screw in the pressure gauge, ensuring it is tight.

4. Fit the pump handle into the actuating lever.

NOTE: Do not locate your press where it will be open to the elements, as it is 

designed to operate at temperatures of between -10

O

C to 40

O

C. Severe 

weather conditions will damage the hydraulic system.

5. Insert the two supporting pins into the lowest holes on the frame, one each 

side.

6. With assistance place the bed on top of the two pins.

BED HEIGHT

Position the bed at the desired height, so as it will be as close as possible to the 
ram when the workpiece is mounted.

IMPORTANT: Due to the weight of the bed, we recommend that you get 
assistance from another person when adjusting the bed height. 

1. Raise one side of the bed, and insert a supporting pin into the next locating 

hole.

2. Repeat at the other end of the bed to level out the bed, 

3. Repeat steps 1 and 2 until the bed is at the desired height, with the 

supporting pins fully ‘home’.

CAUTION: THE BED HEIGHT SHOULD ONLY BE RAISED OR LOWERED 1 
HOLE AT A TIME, WORKING ALTERNATELY FROM ONE SIDE AND THEN THE 
OTHER, FAILURE TO WORK IN THIS WAY MAY CAUSE THE BED TO FALL 
AND CAUSE INJURY TO THE OPERATOR

Содержание 7615103













Отзывы: