Clarke 7610901 Скачать руководство пользователя страница 7

7

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

DISPOSAL OF UNWANTED MATERIALS

One of the most damaging sources of environmental pollution is oil 
products. Never throw away used oil with domestic refuse or flush it 
down a sink or drain. Collect any oil in a leak proof container and 
take it to your local waste disposal site.

Should hydraulic components become completely unserviceable and require 
disposal, draw off the oil into an approved container and dispose of the 
product and the oil according to local regulations.

TROUBLESHOOTING

Problem

Probable Cause

Remedy

Pump unit will not work

Dirt on valve seat/warn 
seals

Bleed pump unit or have 
unit overhauled with new 
seals

Pump will not produce 
pressure
Pump feels hesitant 
under load
Pump will not lower  
completely

Air-lock

Open the release valve 
and remove the oil filler 
plug. Pump the handle a 
couple of full strokes and 
close the release valve. 
Replace the filler plug.

Pump will not deliver 
pressure

Reservoir could be over-
filled or have low oil level.

Check oil level by   
removing the filler plug 
and topping up to the 
correct level.

Pump feels hesitant 
under load

Pump cup seal could be 
worn out.

Have the cup seal 
replaced.

Pump will not lower  
completely

Air-lock

Release air by removing 
the filler plug

Содержание 7610901













Отзывы: