background image

9

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

ENVIRONMENTAL RECYCLING POLICY

Through purchase of this product, the customer is taking on the 
obligation to deal with the WEEE in accordance with the WEEE 
regulations in relation to the treatment, recycling & recovery and 
environmentally sound disposal of the WEEE.

In effect, this means that this product must not be disposed of with general 
household waste. It must be disposed of according to the laws governing 
Waste Electrical and Electronic Equipment (WEEE) at a recognised disposal 
facility.

SPECIFICATIONS

Please note that the details and specifications contained herein, are correct 
at the time of going to print. However, CLARKE International reserve the right 
to change specifications at any time without prior notice.

Model Number

SPP15A

Pump type

Centrifugal

Weight

13.93 kg

Dimensions (L x W x H)

585 x 190 x 280 mm

Max Flow

450 L/min

Max Head

18 m

Operating Temperature

35°C

Water Classification

Swimming Pools/Clean Water

Inlet & Outlet Size

50 i/d / 56 o/d (mm)

Power Supply

220-240V @ 50Hz

Ingress protection rating

IPX5

Output Power

1.5 HP (1150 W)

Sound Power Level

79 dB LwA

Guaranteed Sound Power

82 dB LwA

Содержание 7175036

















Отзывы: