Clarke 6479510 Скачать руководство пользователя страница 11

Страница: 11 / 16

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

SWITCHING ON & OFF

1. Insert the plug into a mains power

socket.

2. Squeeze the trigger to start the

drill.

3. During use, press the trigger lock-

on button and the drill will run
continuously without you needing
to press the trigger.

4. Squeeze the trigger again briefly

to release the trigger lock & stop
the drill.

ADJUSTMENTS

FORWARD / REVERSE SELECTION

1. Set the forward/reverse lever to

the required setting.

SETTING THE SPEED

1. Turn the speed control dial to the

desired level.

NOTE:

The required setting is a

matter of experience.

• Set the dial to a low setting

when drilling into soft or brittle
materials.

• Set the dial to a higher setting when drilling in harder materials, .

CAUTION: THESE ADJUSTMENTS SHOULD ONLY BE PERFORMED WHEN
THE DRILL IS AT A COMPLETE STOP.

Содержание 6479510

















Результаты поиска

Содержание 6479510

Отзывы:

Похожие инструкции для 6479510

Бренды по названию

Популярные бренды

Clarke 6479510, Инструкция по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание 6479510

Отзывы:

Похожие инструкции для 6479510

Бренды по названию

Популярные бренды