Clarke 6460141 Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 32

Clarke 6460141 Скачать руководство пользователя страница 23

23

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

MAINTENANCE AND SERVICING

DAILY/AFTER USE

1. Keep the machine clean using a vacuum cleaner and wipe down with a

damp cloth.

2. Check the saw blade for missing teeth and cracks.

3. Open the top & bottom wheel covers and clean out all saw dust with a

vacuum cleaner.

MONTHLY

1. Open the lower and upper door and check the condition of the wheels,

tyres and blade.

• If required clean the tyres.

2. Using an air line (wearing goggles) blow out the motor casing.

TRANSPORTING THE BANDSAW

• Always transport the tool with

the blade guard in the fully
lowered position so the blade is
fully covered.

• Ensure both upper and lower

doors are locked closed.

• Due to the weight and height

when the saw is fixed to the
stand, it is recommended that
you detach the saw from the
stand when moving the machine.

WARNING: DO NOT USE GUARDS FOR HANDLING OR TRANSPORTATION

«
...
21
22
23
24
25
...
»

Содержание 6460141

































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды