manualshive.com logo in svg

Clarke 6460141, Инструкция по эксплуатации и техническому обслуживанию

Поделиться
Скачать
Clarke 6460141 Скачать руководство пользователя страница 18

18

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

ADJUSTING THE BLADE TENSION

NOTE: 

Ensure the saw is turned 

off and unplugged 
before commencing.

1. Adjust the saw blade so it sits 

dead centre on the rubber 
tyres of the bandsaw wheels.

2. Raise the upper blade guard 

fully (see page 13).

3. Turn the blade tension setting 

knob to required tension. 

• Turning the setting knob clockwise increases the blade tension.

• Turning the setting knob counter clockwise reduces the blade tension.

4. Check the tension by pressing with a finger against the side of the blade, 

halfway between the table and upper guard.

• The blade should not flex more than 2 mm.

TRACKING THE SAW BLADE

If the saw blade does not run on the 
centre of the rubber tyre, the 
tracking needs to be corrected by 
adjusting the tilt of the upper 
bandsaw wheel.

1. Loosen locking nut

2. Turn blade tracking adjustment 

knob:

• Turn clockwise if the saw blade 

runs towards the front of the 
saw

CAUTION: TOO MUCH TENSION CAN CAUSE THE BLADE TO BREAK. TOO 
LITTLE TENSION CAN CAUSE THE BLADE TO MAKE IRREGULAR CUTS.

Содержание 6460141

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды