Clarke 6015700 Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 24

background image

17

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

DATA PLATE INFORMATION

Excessive wear
of the nozzle
and electrodes

1. Air pressure too low

2. Exceeding system capability (material too thick)

3. Contaminated air (humidity-oil)

4. Improperly assembled torch

5. Torch tip contacting workpiece

6. Damaged or loose torch head components

7. Non-genuine manufacturer's parts

Problem

Possible Cause and Likely solution

«
...
15
16
17
18
19
...
»

Содержание 6015700

























Отзывы:

Нет отзывов

Похожие инструкции для 6015700

Бренд: jablotron Страницы: 2

Бренд: jablotron Страницы: 24

Бренд: La Crosse Technology Страницы: 2

Бренд: JBL Страницы: 6

Бренд: KAPTARLIFT Страницы: 16

TripleShield C2S6

Бренд: HOME8 Страницы: 6

Бренд: Keg King Страницы: 4

Бренд: 2N Telekomunikace Страницы: 12

Бренд: Innovative Technology Страницы: 14

7.4VOLT HEATED GLOVES

Бренд: Mobile Warming Страницы: 6

Бренд: Pyle Страницы: 6

Бренд: GEZE Страницы: 16

EVERPURE CONSERV LT-S

Бренд: Pentair Страницы: 20

970114-0403 - X 530 5.1-CH PC Multimedia Home Theater Speaker Sys

Бренд: Logitech Страницы: 10

Magnum Alert 800

Бренд: NAPCO Страницы: 16

Бренд: B-TEC Страницы: 33

Бренд: BMB Страницы: 4

Prestige Close Coupled Systems

Бренд: Rinnai Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды