manualshive.com logo in svg

Clarke 3503596, Руководство по сборке

Поделиться
Скачать
Clarke 3503596 Скачать руководство пользователя страница 3

3

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

GENERAL SAFETY WARNINGS

DO NOT

 use this product in environments for which it is not Intended (i.e. 

extreme cold, high winds, extreme heat, heavy rainfall or heavy snow, etc).

DO NOT

 use open flames or cooking or heating devices inside or in close 

proximity to the garage including all types of stoves, gas heaters, gas lanterns, 
torches, fly killers, etc. The fabric will burn if left in continuous contact with a 
naked flame.

DO NOT

 store flammable liquids (petrol, kerosene, propane, etc.) in the 

garage or operate gas powered vehicles/equipment in or around the 
garage.

ALWAYS 

follow the following instructions for mounting the garage.

Due to the height of this garage, an aerial platform or cherry picker will be 
useful and safer than using ladders. Ensure that any such platforms or ladders 
are operated on level ground.

We advise that 6 people may be required to safely erect the frame and install 
the cover owing to the size and weight

.

Select a calm day to install the cover due to the high windage of the cover 
both during fitting and before it is totally secured in position.

POSITIONING AND INSTALLATION OF THE GARAGE

SITING AND POSITIONING THE GARAGE

This garage is a temporary structure and is not recommended as a permanent 
building. It is designed to offer protection from sun, rain, light snow, tree sap 
and bird droppings etc. It is not designed to shelter equipment from 
excessively high winds or heavy snow.

Choose your garage location carefully. Check for overhead power lines, tree 
branches, etc. 

DO NOT

 install near roofs or other structures that may shed snow, 

ice or excessive run-off onto your garage.

Erect your garage on level ground over a firm, level area. Allow enough 
space near each corner for the tie-down straps supplied to be used as 
intended. If the ground area is of tarmac or concrete, the use of ground 
anchor holding-down bolts will be required to anchor the garage to the floor.

WARNING: READ THESE SAFETY INSTRUCTIONS TO REDUCE THE RISK OF 
INJURY. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.

Содержание 3503596





















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды