Clarke 3503576 Скачать руководство пользователя | Manualshive

Страница: 8 / 16

background image

8

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

STEP 2: ASSEMBLING THE ROOF

1. Assemble the roof frame by connecting the parts layout above.

2. Connect one end of Part #5 with Part #4 using the spring button.

3. Connect the other end of Part #5 with Parts #12 & #13 (See Diagram D1 &

D2) by the fittings #22, #24 & #25.

• There are spring buttons on both end of Part #6. Make sure the

button pops up when connecting with Parts #8, #9 & #11.

4. Use a rubber or wooden mallet if needed to ensure all tubes are fully

inserted.

«
...
6
7
8
9
10
...
»

Содержание 3503576

















Отзывы:

Нет отзывов

Похожие инструкции для 3503576

Бренд: Palram Страницы: 41

Бренд: Jack Wolfskin Страницы: 16

Бренд: Storage Canopy Страницы: 18

Morepork 1 Deluxe

Бренд: Kiwi Camping Страницы: 2

Бренд: Bonga Страницы: 18

Бренд: ABSCO SHEDS Страницы: 29

Бренд: ABSCO SHEDS Страницы: 28

Бренд: ABSCO SHEDS Страницы: 35

Бренд: Sojag Страницы: 23

Бренд: Sojag Страницы: 28

Бренд: Sojag Страницы: 36

Бренд: Ozark Trail Страницы: 1

BUNGALOW GARAGE

Бренд: Nemo Страницы: 8

Бренд: Bestway Страницы: 16

Бренд: Umbrosa Страницы: 34

INGENUA TRIANGLE

Бренд: Umbrosa Страницы: 33

Бренд: Tarasola Страницы: 12

Celebration 30'x40'

Бренд: ARMBRUSTER TENT MAKER Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды