ABSCO SHEDS RG37601N2 Manual Download | Manualshive

Page: 1 / 28

background image

Absco Industries

Assembly Instruction Manual

ABSCO GARAGE

MODEL: RG37601N2

3.7m W x 6.0m D x 3.2m H

Model: RG37601N2

31/08/20

1

AU: 1800 029 70

1

NZ: 0800 466 444

[email protected]

www.abscosheds.com.au

For construction in non-cyclonic areas

Wind rating: N2 as per AS4055-2012.
If you require a higher wind rating please contact
us: [email protected] or 1800 029 701

*The frame must be secured to a concrete slab
or footings, details of which are noted on the
attached engineering drawings. Brackets for
securing the frame to either a concrete slab or
footings are included in this kit. Anchors are not
supplied.

Local authority approval must be obtained prior
to construction. Once you have selected your
site, draw a site plan and lodge your application
together with a copy of the engineering plans
located at the back of these instructions.

Opening width: 2400mm
Opening height: 2300mm
Internal wall height: 2830mm

DOWNLOAD

OUR APP FOR

ASSEMBLY

VIDEOS

LEAVE A REVIEW

Tell us about your experience and

receive a $20 Coles Gift Card.

Visit www.abscosheds.com.au/review

CONCRETE SLAB*

Printed: 02/08/2021 14:21

1
2
3
...
»

Summary of Contents for RG37601N2





























Reviews:

No comments

Related manuals for RG37601N2

Brand: Vango Pages: 2

CANOPIA DALLAS 12x14/3.6x4.3

Brand: Palram Pages: 80

palm club BEACH CABANA

Brand: OZtrail Pages: 8

Brand: DARCHE Pages: 13

Brand: Clarke Pages: 16

Brand: carport Pages: 16

Brand: Gazelle Pages: 4

Brand: Tarptent Pages: 2

Brand: Tarptent Pages: 2

L-GZ815PST-1-PK

Brand: Sunjoy Pages: 5

Brand: Sunjoy Pages: 9

Brand: HI Pages: 13

Brand: ROMAN Pages: 2

Brand: canvascamp Pages: 4

Brand: Bell Tent Pages: 8

Brand: ROBENS Pages: 2

Brand: Vango Pages: 2

Brand: Dancover Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands