background image

12

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

worn or damaged parts. Such servicing and repair work should be carried out 
by a qualified service technician.

PERFORMANCE

Please note that factors other than the tool may effect its operation and 
efficiency such as reduced compressor output, excessive drain on the airline 
moisture or restrictions in the air-line, or the use of connectors of improper size 
or poor condition which will reduce air supply.

**Clarke Air Line Oil (part no. 3050825) is available from your CLARKE dealer.

ACCESSORIES

A wide range of accessories is available including filter/regulators, lubricators, 
high-pressure hoses (5 to 50 metres) etc.

Contact your CLARKE dealer for further information or CLARKE International 
Service Department.

SPECIFICATIONS

Please note that the details and specifications contained herein are correct at 
the time of going to print. However CLARKE International reserve the right to 
change specifications at any time without prior notice. Always consult the 
machine’s data plate.

Model Number

CAT143

Dimensions (L x W x H)

176 x 100 x 44

Weight 0.7 

kg

Air Inlet Size

1/4“BSP (female)

Operating Pressure

90 psi (6.2 bar)

Air Consumption

15 cfm at max load

No Load Speed

20000 rpm @ 90psi

Sound Pressure Level (LpA dB)

88 dB(A)

Sound Power Level (LwA dB)

99 dB(A)

Vibration Levels

2.9 m/s

2

Содержание 3120157

















Отзывы: