background image

  Page  8

                       Clarke

®

 

 American Sanders

 EZ - 8  Sander  Operator's  Manual

MACHINE SET-UP

7.

This sanding machine is designed to be operated
with a remote vacuum dust collection system or
with the included dust bag.  Follow  the procedures
below:

Preparing  Remote Vacuum Dust Collection Systems

To prepare the machine for remote vacuum dust collection
systems that have a 2" hose end, follow this procedure:

1. Install 2" hose  end (figure 9, A) directly over the

exhaust tube (figure 9, B).

2. The exhaust tube can be rotated for optimum conve-

nience.

To prepare the machine for remote vacuum dust collection
systems that have a 1 ½" hose end, follow this procedure:

1. Install the 2" x 1½" hose end adaptor (Part No.

30563A) (figure 9, C) over the exhaust tube (figure 9,
B).

2. Insert 1 ½" hose end (figure 9, D) into the adaptor

(figure 9, C).

NOTE:  Start the remote vacuum collection system
before operation.

Preparing to use the included dust bag

To prepare the machine for use with the included dust bag,
follow this procedure:

1. Install the dust bag by pressing the end onto the

exhaust tube until the ring locks into the groove (figure
10).  This is best done by pressing on the back of the
bag opening with the palm of your hand.

2. The exhaust tube can be rotated for optimum conve-

nience.

3. To remove the dust bag from the exhaust tube, pry up

the end of the bag opening to partially release the
internal rib from the groove, then pull.

4. To empty the dust bag, unzip the disposal flap and

force contents out by inverting the bag.

NOTE: For best results, empty frequently.  Follow all
warnings posted in this manual and on the dust bag.

Install the dust bag by
pressing the end onto the
exhaust tube until the ring
locks into the groove.

1.5" Hose from

vacuum system

(not included)

B

C

Exhaust Tube

(30563A)
2" Tube x 1.5" hose adaptor

Figure 9

Figure 10

A

2" Hose from
vacuum system
(not included)

D

Содержание 07070A























Отзывы: