Reset the unit
Power on/off
Sound adjustment
System setup menu
The RESET button is to be activated for the
following reasons:
- Initial installation of the unit when all
wiring is completed.
- All the function buttons do not operate.
- Error symbol on the display.
1.Turn off the unit power.
2.Press the
(
) button to flip down
the front panel and remove it, then press
the
button with a ballpoint pen or
similar object to restore the unit to the
original factory settings.
if you press
button, the unit can't
work yet, please use a cotton swab soaked
in isopropyl alcohol to clean the socket on
the front panel.
In power off mode, switch on the unit by
pressing any button except the
(
)
button and the
(
) button or
inserting a disc into the slot When the
system is on, press the
(
) button
to turn off the unit.
- Rotate the
button to
adjust volume level.
- Press the
button
repeatedly to select the sound setting that
you would like to adjust: volume, bass,
treble, balance or fader. Rotate the
button to adjust the
level of the selected sound mode:
- VOL: from 00 to 100 (50 levels)
- BAS (bass) / TRB (treble): from -10 to +10
- BAL (Balance): 10L, 9L, ~,L=R, ~, 9R,
10R. Note: L = left, R = right.
- FAD (Fader): 10F, 9F, ~, F=R, ~, 9R, 10R.
Note: F=front; R= rear.
In each mode, when the unit has not been
adjusted for about 5 seconds, the current
setting will be saved and it will return to the
previous mode.
Press the
button and
hold for more than 2 seconds to access the
OPEN
RESET
Note:
RESET
OPEN
EJECT
.
POWER
VOLUME/SELECT
VOLUME/SELECT
VOLUME/SELECT
Note:
VOLUME/SELECT
system setup menu mode, then press the
button to select the
menu item in sequence as follows:
“TA SEEK or TA ALARM”
“PI SOUND or PI
MUTE”
“RETUNE L or RETUNE S”
“MASK DPI or MASK ALL”
“DAB-FM Y or
DAB-FM N”
“BEEPS 2 , BEEP ALL,
BEEP OFF”
After selecting the desired menu item,
rotate the
button to
make the adjustment.
VOLUME / SELECT
VOLUME/SELECT
g
g
g
g
g
ND
“TA SEEK or TA ALARM”
- TA SEEK mode:
- TA ALARM mode:
Note:
“PI SOUND or PI MUTE”:
(search for traffic
announcement/traffic announcement
alarm)
When a newly tuned station does not
receive traffic information for 5 seconds,
the radio retunes to next station which has a
different PI and which broadcasts traffic
information.
If, during the chosen retune time (30
seconds for a short retune or 90 seconds for
a long retune), the unit can no longer
receive the current station which was
broadcasting traffic information, it will start
to search for the next station that has the
same PI.
If no station with the same PI is found after
one search cycle, the radio will search for
the next station broadcasting traffic
announcements.
Select this mode to switch off the automatic
retune. The radio will then emit a double
beep sound (ALARM).
If a newly tuned station does not broadcast
any traffic information for 5 seconds, a beep
can be heard.
If the unit can no longer receive the current
station during the chosen retune time, a
beep sound can also be heard.
If a newly tuned station has no RDS signal,
the message “PI SEEK” disappears.
TP: Traffic Program.
PI: Program Identification.
In some regions, there is a possibility of
having two different stations with the same
frequency but different PI codes.
If “PI SOUND” is selected, radio will switch
to the new station with a different PI for a
General Operations
