manualshive.com logo in svg

Clarion Ungo Pro Security RK1, Руководство по установке

Поделиться
Скачать
Clarion Ungo Pro Security RK1 Скачать руководство пользователя страница 40

40

override mode

To enter or exit Override mode with the Override switch:

1. Turn the ignition on and then off.

2. Within 10 seconds, press and release the Override switch.

The status LED will light solid if you have entered override mode, and will go out if you have exited
override mode.

safety check

Before vehicle reassembly, the remote system must be checked to ensure safe and trouble-free oper-
ation. The following test procedure must be used to verify proper installation and operation of the
system. The installation must be completed before testing, including connection to the brake switch
and hood switch.

1. Test the BRAKE shutdown circuit: With the vehicle in Park (P), activate the remote start system.

Once the engine is running, press the brake pedal. The engine should shut down immediately. If
the engine continues to run, check the brake circuit connection.

2. Test the HOOD PIN shutdown circuit: With the vehicle in Park (P), open the hood. Activate the remote

start system. The vehicle should not start. If the starter engages, check your hood pin and connections.

N

Noottee:: If programmed for Diesel Mode, the system will turn on the ignition, but the starter should not engage with
the hood open.

3. Test the NEUTRAL SAFETY shutdown circuit: 

IIm

mp

poorrtta

anntt!! Make sure there is adequate clearance to the front and rear of the vehicle before attempting this test. 

a. Make sure the hood is closed and no other shutdown circuits are active.
b. Set the emergency brake. 
c. Turn the ignition key to the run position but do not start the engine.
d. Put the vehicle in Drive (D).
e. Put your foot over the brake pedal but do not press down on it. Be ready to step on the brake

to shutdown the remote start system.

f. Activate the remote start system.

Содержание Ungo Pro Security RK1















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды