manualshive.com logo in svg

Clarion Ungo Pro Security RK1, Руководство по установке

Поделиться
Скачать
Clarion Ungo Pro Security RK1 Скачать руководство пользователя страница 16

16

H1/11 RED

(+)12V constant power input

Before connecting this wire, remove the supplied fuse. Connect to the battery positive terminal or the
constant 12V supply to the ignition switch. 

N

NO

OTTEE:: Always use a fuse within 12 inches of the point you obtain (+)12V. Do not use the 10A fuse in the har-

ness for this purpose. This fuse is intended to protect the module.

H1/12 RED/WHITE

Channel 2, (-) 200 mA output

When the system receives the code controlling Channel 2, for longer than 1.5 seconds, the
RED/WHITE wire will supply an output as long as the transmission continues. This is often used to
operate a trunk/hatch release or other relay-driven function.

IIM

MPPO

ORRTTA

AN

NTT!! Never use this wire to drive anything except a relay or low-current input! The transistorized output

can only supply 200 mA of current. Connecting directly to a solenoid, motor, or other high-current device will
cause it to fail.

relay satellite connecting to key switch
wire connection guide

All except the red heavy gauge wires leading from the relay satellite are used to energize high cur-
rent circuits in the vehicle. It is crucial that these connections are made correctly so that they are
capable of handling the current demands. For this reason, scotch locks, T-taps and other such con-
nectors should not be used.

PURPLE

(+) starter output

After cutting the starter wire connect the PURPLE wire to the end going to the starter motor.

GREEN

starter kill

After cutting the starter wire connect the GREEN wire to the end going to the key side of the ignition switch.

Содержание Ungo Pro Security RK1















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды