Clarion FZ709E, Руководство пользователя

Страница: 11 / 40

15
English
FZ709E
Basic Operations
Adjusting the M-BEX
3 - 1 .
Select “ M-BEX ”.
3 - 2 .
Touch [ ] key to enter detail setting stage.
3 - 3 .
Slide along [ ] slider or touch [ ]/[ ]
key to turn on or turn off the MAGNA BASS
EXTEND effect.
∗
The factory default setting is “ OFF ”.
(Adjustment range: ON/OFF)
3 - 4 .
After completing settings, touch the [ ENT
]
key to return to the 1
st
selected item.
Adjusting the fader
3 - 1 .
Select “ FADER ”.
3 - 2 .
Touch [ ] key to enter detail setting stage.
3 - 3 .
Slide along [ ] slider or touch [ ]/[ ]
key to adjust the balance of the rear and front
speakers.
∗
The factory default setting is “ CENTER ”.
(Adjustment range: FRONT 12 to REAR 12)
3 - 4 .
After completing settings, touch the [ ENT
]
key to return to the 1
st
selected item.
Adjusting the balance
3 - 1 .
Select “ BALANCE ”.
3 - 2 .
Touch [ ] key to enter detail setting stage.
3 - 3 .
Slide along [ ] slider or touch [ ]/[ ]
key to adjust the balance of the right and left
speakers.
∗
The factory default setting is “ CENTER ”.
(Adjustment range: RIGHT 12 to LEFT 12)
3 - 4 .
After completing settings, touch the [ ENT
]
key to return to the 1
st
selected item.
When “ON” is set:
3 - 3 - 1 .
Touch [ ] key to enter detail setting
stage.
3 - 3 - 2 .
Slide along [ ] slider or touch [ ]/[ ]
key to select the value in sequence of
“ HIGH ” “ MID ” “ LOW ”
∗
The factory default setting is “ MID ”.
3 - 4 .
After completing settings, touch the [ ENT
]
key to return to the 1
st
selected item.
Adjusting the high pass filter
3 - 1 .
Select “ HPF ”.
3 - 2 .
Touch [ ] key to enter detail setting stage.
3 - 3 .
Slide along [ ] slider or touch [ ]/[ ]
key to select the setting in sequence
“ 60 ” “ 90 ” “ 120 ” “ THROUGH ”
∗
The factory default setting is “ THROUGH ”.
∗
This is supported only with amplifiers
equipped with this function. Output is not
supported from RCA cables.
Adjusting the subwoofer output
volume
You can adjust the volume output from the unit’s
subwoofer output terminal.
This adjustment can be performed only when the
“ S-W LPF ” is set to “ 60 ”, “ 90 ” or “ 120 ”.
3 - 1 .
Select “ S-W VOL ”.
3 - 2 .
Touch [ ] key to enter detail setting stage.
3 - 3 .
Slide along [ ] slider or touch [ ]/[ ]
key to increases or decreases the subwoofer
volume.
∗
The factory default setting is “ 0 ”.
(Adjustment range: +6 to -6)
Note:
During SOUND adjustment mode, if no operation
is performed for more than 10 seconds, this mode
can be cancelled and return to previous mode.
Setting the subwoofer
You can set the low pass filter of subwoofer.
3 - 1 .
Select “ S-W LPF ”.
3 - 2 .
Touch [ ] key to enter detail setting stage.
3 - 3 .
Slide along [ ] slider or touch [ ]/[ ]
key to select the setting in sequence
“ THROUGH ” “ 60 ” “ 90 ” “ 120 ”
∗
The factory default setting is “ THROUGH ”.
∗
When the volume level is more than 30, the
subwoofer volume adjustment value can not
reach +6.