manualshive.com logo in svg

Clack Valves WS1.5, Инструкция по установке и обслуживанию, Страница: 14 / 52

Поделиться
Скачать
Clack Valves WS1.5 Скачать руководство пользователя страница 14

Page 14  

WS1.5", 2" and 2"QC Drawings and Service Manual

3) Main Piston and Regenerant Piston

Disassembly and Inspection
Attached to the drive cap assembly is the main piston and depending on the con

fi

 guration, a regenerant piston. The regenerant piston 

(the small diameter one behind the main piston) is removed from the main piston by unsnapping it from its disassembly latch. To 
remove the main down 

fl

 ow piston fully extend the piston rod and then unsnap the main piston from its latch by pressing on the side 

with the number. Chem i cal ly clean the piston in dilute sodium bisul

fi

 te or vinegar, or replace the them. The main piston is te

fl

 on 

coated. If the te

fl

 on coating is abraided, replace the main piston.

Reassembly
Reattach the main piston to the drive cap assembly. Reattach the regenerant piston (if needed) to the main piston. Reinsert the drive 
cap assembly and piston into the spacer stack assembly and hand tighten the drive cap assembly. Continue to tighten the drive cap 
assembly until the backside of the drive cap bottoms out 

fl

 ush with the casting or the black o-ring on the spacer stack assembly is no 

longer visible through the drain port. Excessive force can break the notches molded into the drive back plate. Make certain that the 
main drive gear still turns freely. The exact position of the piston is not important as long as the main drive gear turns freely.

Reattach the drive assembly to the control valve and connect all plugs. After completing any valve maintenance, press and hold 
NEXT and REGEN buttons for 3 seconds or unplug power source jack (4 pin, black cable) and plug back in. This resets the 
electronics and establishes the service piston position. The display should 

fl

 ash all wording, then 

fl

 ash the software version and then 

reset the valve to the service position.

4) Spacer Stack Assembly

Disassembly and Inspection
To access the spacer stack assembly remove the drive assembly, drive cap assembly and piston. The spacer stack assembly can then 
be pulled straight out. Inspect the black o-rings and inner seals for wear or damage, re place the entire stack if necessary. Do not 
disassemble the stack. 

The spacer stack assembly may be chemically cleaned (dilute sodium bisul

fi

 te or vinegar) or wiped with a soft cloth. 

Reassembly
The spacer stack assembly can be pushed into the control valve body bore by hand. The assembly is properly seated when at least 
four threads are exposed (approximately 5/8”). Do not force the spacer stack as sem bly in. The control valve body bore interior can 
be lubricated with silicone to allow for easy insertion of the entire stack.

Reattach the drive cap assembly and piston(s) and the drive assembly.

After completing any valve maintenance, press and hold NEXT and REGEN buttons for 3 seconds or unplug the power source jack 
(4 pin, black cable) and plug back in. This resets the electronics and establishes the service piston position. The display should 

fl

 ash 

all wording, then 

fl

 ash the software version and then reset the valve to the service position.

Содержание WS1.5





















































Отзывы:

Нет отзывов