Claas MEDION 310 Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 51

background image

299 216.0 - RHB MEDION 340 - 310

1.2.3

Safety rules

Leaving the machine

1. When leaving the machine, ensure that it

will not roll away (apply parking brake, wheel
chocks). Stop the engine, remove the ignition
key and, if required, lock the cab! – Disconnect
the battery isolating switch!

2. Never leave the machine unattended as long

as the engine is still running!

3. Lower the front attachments fully to the ground

before leaving the machine!

Compressor-type air conditioner

1. The cooling system is filled with

FHC refrigerant R 134 A. FHC refrigerants
must not be vented to the atmosphere! There-
fore, please take appropriate precautions when
working on the compressor-type air conditioner.

2. Maintenance and repairs are only to be carried

out by competent, professional service centres
qualified to handle refrigerants. Refrigerant
must always be sucked out and disposed of for
recycling.

Maintenance

1. Repair, service and cleaning work as well as

the elimination of malfunctions should only be
performed with the drives stopped and the
engine switched off. Remove the ignition
key (main switch key).

2. Escaping fluid (fuel, hydraulic oil, etc.) under

high pressure can penetrate the skin and cause
serious injury. If any fluid is injected into the
skin, consult a doctor immediately as otherwise
serious infections may result!

3. Always turn off the battery isolating switch

before carrying out any electrical repairs on
the machine!

4. Be careful when opening the radiator cap.

As long as the engine is hot, the radiator is
under pressure!

5. Dispose of oil, fuel and filters in a way that is

harmless to the environment and in accordance
with existing anti-pollution regulations!

6. Do not attempt to mount a tyre unless you

have the proper equipment and experience
to perform the job safely.

7. Retighten the wheel nuts regularly!

8. Only have qualified workshops carry out repair

work on the hydraulic system.

9. Always disconnect the battery isolating switch

during maintenance work on the machine and
on the engine.

Basic rule

Always check the operational safety and road
safety of the machine before starting the engine!

Hydraulic accumulators

Be especially careful when working on the accumu-
lators! Accumulators are under high pressure!

With valve-controlled hydraulic accumulators – as
for example on the CLAAS Autopilot – first slacken
the short-circuit bolt before carrying out any repair
work at the hydraulic accumulator. This is neces-
sary to relieve the hydraulic pressure.

«
...
19
20
21
22
23
...
»

Содержание MEDION 310




















































Отзывы:

Нет отзывов

Похожие инструкции для MEDION 310

Бренд: Landoll Страницы: 6

Бренд: ParaBody Страницы: 9

Бренд: ParaBody Страницы: 3

Бренд: MacDon Страницы: 45

Бренд: H&S Страницы: 30

ImageQuant LAS 4000

Бренд: GE Страницы: 86

Бренд: GE Страницы: 160

Бренд: GE Страницы: 134

Бренд: YMC Страницы: 49

Бренд: Octane Fitness Страницы: 8

Бренд: Octane Fitness Страницы: 10

Бренд: OCENCO Страницы: 48

Бренд: Ocean Optics Страницы: 6

Бренд: S.R.Smith Страницы: 8

Бренд: S.R.Smith Страницы: 23

NavBoard ZipFlip

Бренд: S&S Precision Страницы: 6

Бренд: Waters Страницы: 250

Бренд: Waters Страницы: 141

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды