Claas LEXION 620 Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 56

background image

24

Service Maintenance

1.End to end guides

Correct tension is
achieved when the ends
of “D” are end to end. To
tension the belt, slacken
nut K from M and wind M
in a clockwise direction
until the ends of D meet
then lock nuts M and K. If
the belt needs removing
please consult section 14
of the operator’s manual.

2.Centre to centre guides

Work in exactly the same way
as the end to end tensioners
except the belt is at the correct
tension when the tabs overlap
the full length of the recessed
part of the tabs.

3. Gold tube type

Under the correct tension the
gold tube should be just able to
turn by hand, if loose it will need
tightening. To tension slacken
Nut K slightly, tighten “R” until it
meets the gold tube. It should
still be possible to rotate the
tube by hand with a firm grip.
Then lock the assembly with
the nut K.

«
...
22
23
24
25
26
...
»

Содержание LEXION 620

























































Отзывы:

Нет отзывов

Похожие инструкции для LEXION 620

Бренд: Rangevision Страницы: 31

Бренд: DARKSTAR TECHNOLOGIES Страницы: 4

Бренд: TDW Страницы: 2

Бренд: Taurus Страницы: 25

Бренд: Vancare Страницы: 3

Бренд: Paitec Страницы: 14

Precision2 HP2 Series

Бренд: B-K lighting Страницы: 6

Бренд: Zero Hand Truck Страницы: 38

Бренд: B-K lighting Страницы: 3

Бренд: Parker Research Corp Страницы: 4

Бренд: Eastwood Страницы: 20

Бренд: Daihan Scientific Страницы: 43

Бренд: ParaBody Страницы: 5

Бренд: Gebhardt Anlagentechnik Страницы: 152

Бренд: Hach Страницы: 58

Бренд: Hach Страницы: 52

Бренд: Wahl Страницы: 2

Бренд: Zell Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды