City Theatrical QolorFLEX 4x5A DINrail Dimmer, Быстрый старт

Страница: 2 / 2

© City Theatrical 20 22
Revision 1. 3
DMX Address is 001,CH04
DMX Start Address-
Output Resolution-
Device DMX Proles
Dimming Curve
Control Interface
8888
Select
(Select)
Enter
(Enter)
Up Down
The six function menus are:
DMX Address PWM Frequency
Dimming Curve Value
Operating Prole
DMX Channel Qty
Output Resolution
(Factory default is 001)
(Factory default is 16)
(Factory default is 1.1)
(Factory default is 1.5 )
08 or 16
00 thru 30
0.1 thru 9.9
DMX Channel Qty-
(Factory default is 0
4
)
SETTINGS:
CH01 : DMX addresses 1,2,3,4 = 001
CH02 : DMX addresses, 1,3 =001, 2,4 =002
CH03 : DMX addresses, 1,2 =001, 3 =002, 4 =003
CH04 : DMX addresses, 1 =001, 2 =002, 3 =003,
4 =004
A00 i
ch05
i6
9a i5
pf0 i
I i
Values:
00 = 500Hz
01 to 30 = 1kHz to 30kHz
PWM Frequency
(Factory default is 0
5
)
PWM frequency is used to tune the dimmer for
flicker free operation when used with high
speed cameras. A high PWM value produces
the least amount of flicker. A low PWM value
produces better dimming quality. Always
perform a camera test to confirm optimal results.
The Dimming Curve may be adjusted to
affect the rate of rise and fall of the dimmer.
Values less than 1.0 increase the rate, while
values greater than 1.0 decrease the rate.
(1.0 is linear)
Resolution determines the smoothness of the
dimming. 8 bit uses one DMX channel, while
16 bit uses two.
Sets the DMX address for the dimmer.
Operation:
1. Press “Up” to scroll thru
menu choices
2. Press “Select” to enable
programming- (display ashes)
3. Use “Up” or “Down” buttons to
set values
4. Press “Enter” to save value.
AVAILABLE SETTINGS:
AVAILABLE SETTINGS:
AVAILABLE SETTINGS:
LIGHT
OUTPUT
DMX CONTROL SETTING
<1
>1
1.5
1.0
2.5
3.5
6.5
0.9
0.8
Channel 1
Channel 2
Channel 3
Channel 4
Channel 5
Channel 6
Channel 7
Channel 8
Channel 1
Channel 2
Channel 3
Channel 4
Channel 5
Channel 6
Channel 1
Channel 2
Channel 3
Channel 4
Channel 1
Channel 2
dp1.1
dp1.1
dp1.1
dp1.1
dp2.1
dp2.1
dp2.1
dp2.1
dp3.2
dp4.3
dp5.4
dp5.3
dp6.4
For output 1,3
dimming
For output 1
dimming
For output 1
dimming
For output 1
dimming
For output 1
dimming
For output 2
dimming
For output 2
dimming
For output 2
dimming
For output 2
dimming
For output 3
dimming
For output 3
dimming
For output 3
dimming
For output 4
dimming
For output 4
dimming
For output 4
dimming
For output 2
dimming
For output 2
dimming
For output 1
dimming
For output 1
dimming
For output 2,4
dimming
For output 3,4
dimming
For output 3,4
dimming
For output 3,4
dimming
For output 2,4
dimming
For output 1,3
dimming
For all output
dimming
Strobe Effects
Strobe Effects
For all output
dimming
For all output
dimming
For all output
dimming
For all output
dimming
For all output
dimming
For all output
dimming
For output 1
dimming
For output 4
dimming
For output 4
Fine dimming
For output 2
dimming
For output 3
dimming
For output 2
dimming
For output 1
dimming
For output 1
Fine dimming
For output 1
Fine dimming
For output 2
Fine dimming
For output 2
Fine dimming
For output 3
Fine dimming
For output 2,4
dimming
For output 3,4
dimming
For output 3,4
Fine dimming
For output 2,4
Fine dimming
For output 1,3
dimming
For output 1,3
Fine dimming
For all output
dimming
For all output
Fine dimming
Note*- To restore factory defaults, press and hold both
“Enter” and “Select” for
five
seconds until display
goes out.
DMX Address is 001,CH01
DMX Address is 001,CH02
DMX Address is 001,CH03
Should the dimmer experience an input voltage issue or output
overload the display will flash repeatedly.
Once the issue is corrected, power cycle to reset the unit.