16. OBJECT AND LIQUID ENTRY
Do not push objects through any openings in this unit, as they may touch dangerous voltage points or
short out parts that could result in fire or electric shock. Never spill or spray any type of liquid into the
unit.
17. OUTDOOR ANTENNA GROUNDING
If an outside antenna or cable
system is connected to the unit, be
sure the antenna or cable system is
grounded to provide some
protection against voltage surges
and built-up static charges, Section
810 of the National Electrical Code
(NEC), ANSI/NFPA 70, provides
information with respect to proper
grounding of the mast and
supporting structure, grounding
18. SERVICING
Do not attempt to service this unit yourself as opening or removing covers may expose you to
dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
19. DAMAGE REQUIRING SERVICE
Unplug this unit from the wall outlet and refer servicing to qualified service personnel under the
following conditions:
a. When the power-supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into the unit.
c. If the unit has been exposed to rain or water.
d. If the unit does not operate normally by following the operating instructions. Adjust only those
controls that are covered by the operating instructions, as an improper adjustment of other
controls may result in damage and will often require extensive work by a qualified technician
to restore the unit to its normal operation.
e. If the unit has been dropped or the cabinet has been damaged.
f. When the unit exhibits a distinct change in performance, this indicates a need for service.
20. REPLACEMENT PARTS
When replacement parts are required, be sure the service technician uses replacement parts specified
by the manufacturer or those that have the same characteristics as the original part.
Unauthorized substitutions may result in fire, electric shock or other hazards.
21. SAFETY CHECK
Upon completion of any service or repairs to this unit, ask the service technician to perform safety
checks to determine that the unit is in proper operating condition.
22. HEAT
The product should be situated away from heat sources such as radiators, heat registers, stoves, or
other products (including amplifiers) that produce heat.
23. CONNECTING
When you connect the product to other equipment, turn off the power and unplug all of the equipment
from the wall outlet. Failure to do so may cause an electric shock and serious personal injury. Read
the owner's manual of the other equipment carefully and follow the instructions when making any
connections.
24. SOUND VOLUME
Reduce the volume to the minimum level before you turn on the product. Otherwise, sudden high
volume sound may cause hearing or speaker damage.
25. SOUND DISTORTION
Do not allow the product output distorted sound for a longtime. It may cause speaker overheating and
fire.
26. HEADPHONES
When you use the headphones, keep the volume at a moderate level. If you use the headphones
continuously with high volume sound, it may cause hearing damage.
27. LCD
Should the LCD panel be broken and liquid leaks out, do not inhale or swallow it. Doing so may cause
poisoning. If you have got it into your mouth, wash it out and consult your doctor. If your hands or
clothes have touched it, wipe them with alcohol and a cleaning cloth and then wash them well.
28. NOTE TO CABLE TV SYSTEM INSTALLER
This reminder is provided to call the Cable TV system installer’s attention to Article 820-40 of the NEC
that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be
connected to the grounding system of the building, as close to the point of cable entry as practical.
B- Input mode: AV Video, S-Video
1) Press key
MENU
Table 4
Name of submenu Picture of submenu
Instructions
Colour
1. Brightness adjust.
2. Contrast adjust.
3. Colour adjust
4. Exit menu.
Picture
1. Picture horizontal position adjust.
2. Picture vertical position adjust.
3. Picture sharpness adjust.
4. Picture phase adjust.
5. Picture clock adjust.
6. Exit menu.
Function
1. Set clock, phase and position of
the video automatically.
2. Auto adjustment of the input video
position.
3. Auto adjustment of the sampling
phase.
4. Auto adjustment of the sampling clock.
5. Exit menu.
OSD Menu
1. OSD language select.
2. OSD horizontal position adjust.
3. OSD vertical position adjust.
4. OSD disappear timer select.
5. OSD translucent select.
6. Exit menu.
11
2