Citizen BD2-2860 Скачать руководство пользователя страница 25

Страница: 25 / 81

BD2-2860 User’s Manual

CITIZEN

8.2 Operation Errors

(1)Error types

Error

Description

No paper

The printing paper set is not set

Head –up

The head-up lever is at its up position

VH voltage error

A VH voltage is beyond its allowable range (4.2 to 8.5V)

Head temperature error

A head temperature is less than 0

C or 65

C or higher.

Cutter lock

(ACS-220-5V)

When driving the cutter, the cutter is locked due to an external factor (Paper jam,
etc.).

Note 1) The 8.5V upper-limit voltage for VH voltage error is only an assumptive voltage just after charging the

battery when using the battery power. It cannot be normally used. A normal maximum voltage is 7.2V.

(2) External signal outputs

Interface Connector (CN3)

Pin No.

Signal Name

Remarks

ERROR

LED output. For a blinking (Lighting) pattern, see 8.3 Error Indication.

PE OUT

LED output. This is always o utput at the time of no paper.

DTR

Serial interface

BUSY

Parallel interface

FAULT

Parallel interface

(3) Resetting methods

Error

Resetting Method

No paper

Set the paper. See Note 1.

Head –up

Bring down the head-up lever.

VH voltage error

Set to a voltage within the allowable range (4.2 to 8.5V) and turn on the power
again. Alternatively, activate the Pin19 (LFSW) of the CN3(interface connector).

Head temperature error

At the lower limit (less than 0

C), printing becomes operational at 0

C higher.

At the upper limit (65

C or higher), it become operational at 60

C or lower.

Cutter lock

(ACS-220-5V)

Eliminate paper jam and activate the Pin19(LFSW) of the CN3(Interface
Connector) or turn on the power again.

Note 1) When auto loading has not been selected with the function selection jumper(J4), set the paper manually.

When it has been selected, the auto loading function is enabled to facilitate replacement of the paper.

Note 2) The 8.5V upper-limit voltage for VH voltage error is only an assumptive voltage just after charging the

battery when using the battery power. It cannot be normally used. A normal maximum voltage is 7.2V.

Содержание BD2-2860


















































































Результаты поиска

Содержание BD2-2860

Отзывы:

Похожие инструкции для BD2-2860

Бренды по названию

Популярные бренды

Citizen BD2-2860, Руководство пользователя

Результаты поиска

Содержание BD2-2860

Отзывы:

Похожие инструкции для BD2-2860

Бренды по названию

Популярные бренды