background image

Page 5

CISSELL  DRYER  WARRANTY

The Cissell Manufacturing Company (Cissell) warrants all new equipment (and the original parts thereof) to be free from

defects in material or workmanship for a period of three (3) years from the date of sale thereof to an original purchaser for

use, except as hereinafter provided. With respect to non-durable parts normally requiring replacement in less than three (3)

years due to normal wear and tear, and with respect to all new repair or replacement parts for Cissell equipment for which

the three (3) year warranty period has expired, or for all new repair or replacement parts for equipment other than Cissell

equipment, the warranty period is limited to ninety (90) days from date of sale. The warranty period on each new replacement

part furnished by Cissell in fulfillment of the warranty on new equipment or parts shall be for the unexpired portion of the

original warranty period on the part replaced.

With respect to electric motors, coin meters and other accessories furnished with the new equipment, but not manufactured

by Cissell, the warranty is limited to that provided by the respective manufacturer.

Cissell's total liability arising out of the manufacture and sale of new equipment and parts, whether under the warranty or

caused by Cissell's negligence or otherwise, shall be limited to Cissell repairing or replacing, at its option, any defective

equipment or part returned f.o.b. Cissell's factory, transportation prepaid, within the applicable warranty period and found

by Cissell to have been defective, and in no event shall Cissell be liable for damages of any kind, whether for any injury to

persons or property or for any special or consequential damages. The liability of Cissell does not include furnishing (or

paying for) any labor such as that required to service, remove or install; to diagnose troubles; to adjust, remove or replace

defective equipment or a part; nor does it include any responsibility for transportation expense which is involved therein.

The warranty of Cissell is contingent upon installation and use of its equipment under normal operating conditions. The

warranty is void on equipment or parts; that have been subjected to misuse, accident, or negligent damage; operated under

loads, pressures, speeds, electrical connections, plumbing, or conditions other than those specified by Cissell; operated

or repaired with other than genuine Cissell replacement parts; damaged by fire, flood, vandalism, or such other causes

beyond the control of Cissell; altered or repaired in any way that effects the reliability or detracts from its performance,

or; which have had the identification plate, or serial number, altered, defaced, or removed.

No defective equipment or part may be returned to Cissell for repair or replacement without prior written authorization

from Cissell. Charges for unauthorized repairs will not be accepted or paid by Cissell.

CISSELL  MAKES  NO  OTHER  EXPRESSED  OR  IMPLIED  WARRANTY,  STATUTORY  OR OTHERWISE,

CONCERNING  THE  EQUIPMENT  OR  PARTS  INCLUDING,  WITHOUT LIMITATION,  A  WARRANTY  OF

FITNESS  FOR  A  PARTICULAR  PURPOSE,  OR  A WARRANTY  OF  MERCHANTABILITY.   THE
WARRANTIES  GIVEN  ABOVE  ARE  EXPRESSLY IN  LIEU  OF  ALL  OTHER  WARRANTIES,  EXPRESSED

OR  IMPLIED.   CISSELL  NEITHER ASSUMES,  NOR  AUTHORIZES  ANY  PERSON  TO  ASSUME  FOR  IT,

ANY  OTHER WARRANTY  OR  LIABILITY  IN  CONNECTION  WITH  THE  MANUFACTURE,  USE  OR  SALE  OF ITS
EQUIPMENT  OR  PARTS.

For warranty service, contact the distributor from whom the Cissell equipment or part was purchased. If the distributor
cannot be reached, contact Cissell.

IDENTIFICATION NAMEPLATE

The identification nameplate is located on the rear wall of the dryer. It contains the dryer serial number, product number, model

number, electrical specifications and other important data that may be needed when servicing and ordering parts, wiring diagrams,

etc. Do not remove this nameplate.

Содержание HD50.1
































































Отзывы: