background image

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

Operation

AJ1032

10

NOTE: The following instructions will OPTIMIZE 
garment quality and prolong padding life.

Pre-Operating Services

Perform the following services daily before using 
press:

1. Check condition of buck padding. Padding 

should be replaced if:

Cover is scorched or torn.

Cover is hard, brittle or not springy.

2. Open air supply line and downstream relief shut-

off valves. If press is equipped with a timer, close 
electrical disconnect switch or circuit breakers.

3. Simultaneously push and hold both CLOSE 

pushbuttons (Items 1 and 6, 

Figure 2

) until head 

is closed against buck.

4. Release CLOSE pushbuttons. Head should 

remain closed.

5. Push OPEN pushbutton (Item 5, 

Figure 2

). Head 

should open.

6. Simultaneously push both CLOSE pushbuttons. 

As head travels downward, release left 
pushbutton. Head should return open.

7. Simultaneously push both CLOSE pushbuttons. 

As head travels downward, release right 
pushbutton. Head should return open.

8. Simultaneously push both CLOSE pushbuttons. 

Have a second person press the OPEN 
pushbutton as you continue pressing the CLOSE 
pushbuttons. Head should open.

9. If pushbuttons do NOT perform as described in 

steps 3 through 8, do NOT operate press. Call a 
qualified service technician.

10. Slowly open steam supply and return shut-off 

valves to prevent water hammer in steam pipes. 
Allow 15 to 20 minutes for press to heat.

Press Operation

One complete pressing operation is described in the 
following steps.

Presses WITHOUT Timers or Presses 
WITH Timer Set to OFF Position

1. Perform pre-operating services.

2. If press is equipped with a timer, place switch 

(Item 4, 

Figure 2

) in OFF position.

3. Dress garment on buck.

4. Simultaneously push and hold both CLOSE 

pushbuttons (Items 1 and 6, 

Figure 2

) until head 

closes and pressing pressure is applied. Release 
both pushbuttons. 

NOTE: If either pushbutton is released BEFORE 
pressing pressure is applied, head will return to a 
fully OPEN position.

5. Once garment is sufficiently pressed, press 

OPEN pushbutton (Item 5, 

Figure 2

) to open 

press.

6. Hang or fold pressed article as soon as possible to 

preserve finish.

Presses With Timers ONLY

1. Perform pre-operating services.

2. Place timer switch (Item 4, 

Figure 2

) in the ON 

position.

3. Set time selector knob (Item 2, 

Figure 2

) t

desired time.

NOTE: Proper time required for pressing varies 
with garment material and moisture retention. Set 
timer so pressing pressure is applied long enough to 
set a press. Proper time is best determined by 
experience.

4. Dress garment on buck.

5. Simultaneously push and hold both CLOSE 

pushbuttons (Items 1 and 6, 

Figure 2

) until head 

closes and pressing pressure is applied. Release 
both pushbuttons. 

To avoid possible serious injury when 
cleaning or repairing traps or strainers:
• Shut off AND lock out ALL steam service 

to press.

• Let heated surface cool.

W340

WARNING

To avoid possible serious injury:
• Perform steps 3 through 8 daily before 

using press.

• Do NOT use press if ANY step is not 

performing properly.

W341

WARNING

Содержание AJ1032























Отзывы: