Cisco WRP500 Скачать руководство пользователя страница 109

Страница: 109 / 128

R E V I E W D R A F T # 1 — C I S C O C O N F I D E N T I A L

B-19

Cisco WRP500 Administration Guide

Appendix B Data Fields

Applications and Gaming

The Applications and Gaming module includes the following pages:

•

“Applications and Gaming > Single Port Forwarding” on page 19

•

“Applications and Gaming > Port Range Forwarding” on page 20

•

“Applications & Gaming > Port Range Triggering” on page 21

•

“Applications & Gaming > DMZ” on page 21

•

“Applications and Gaming > QoS (Quality of Service)” on page 21

Applications and Gaming > Single Port Forwarding

Access Restriction

Deny: Prevent the listed computers from accessing the
Internet.

Allow: Permit the listed computers to access the
Internet.

Schedule

The days and times when the policy is enforced. The
Everyday option applies the policy to all days of the
week, or you can specify the days. The 24 Hours option
applies the policy to all hours of the specified days, or
you can speciy the time range.

Website Blocking by URL
Address

A list of website addresses that users are prevented
from accessing.

Website Blocking by Keyword

A list of keywords that are used to prevent access to
inappropriate websites.

Blocked Applications

A list of applications, such as FTP, that users are
prevented from using. Up to three applications can be
blocked for each policy.

Application Name

A name for the application. Each name can be up to 12
characters.

External Port

The external port number used by the server or Internet
application. Check with the Internet application
documentation for more information.

Internal Port

The internal port number used by the server or Internet
application. Check with the Internet application
documentation for more information.

Protocol

The protocol used for this application, either TCP,
UDP, or both.

Содержание WRP500

































































































































Результаты поиска

Содержание WRP500

Отзывы:

Похожие инструкции для WRP500

Бренды по названию

Популярные бренды

Cisco WRP500, Руководство администратора

Результаты поиска

Содержание WRP500

Отзывы:

Похожие инструкции для WRP500

Бренды по названию

Популярные бренды