Cisco UBR7246VXR Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 28

background image

C H A P T E R

4-1

Cisco Cable Clock Card Hardware Installation Guide for the Cisco uBR7246VXR Universal Broadband Router

OL-26705-01

4

Configuring the Clock Card

To continue the Cisco Cable Clock Card installation, you must configure the primary and/or secondary
T1 interfaces. This chapter contains the following sections:

•

Minimum Software Requirements, page 4-1

•

Configuration and Diagnostic Cisco IOS Commands for the Clock Card, page 4-2

Minimum Software Requirements

You must have Cisco IOS Release 12.1(1a)T1 or later, and Cisco IOS Release 12.1(2)EC1 or later if you
are configuring the clock card with a Cisco uBR-MC16S or Cisco uBR-MC16E cable interface line card.
If you are using a Cisco uBR-MC28C cable interface line card with the clock card, you must use
Cisco IOS Release 12.1(3a)EC1 or later. If you are using a Cisco uBR-MC28U/X card, you must use
Cisco IOS Release 12.2(15)CX or later.

Note

You can use other cable interface cards, such as the Cisco uBR-MC16C, with the clock card, but these
other cable interfaces will not synchronize their downstream SYNC messages with the external clock
source.

«
...
21
22
23
24
25
...
»

Содержание UBR7246VXR





























Отзывы:

Нет отзывов

Похожие инструкции для UBR7246VXR

Бренд: Watchguard Страницы: 40

EtherLink 3C509B

Бренд: 3Com Страницы: 8

Бренд: 3Com Страницы: 8

Бренд: A-Link Страницы: 6

Бренд: NAIM Страницы: 2

Бренд: Zenith Data Systems Страницы: 64

Бренд: NETGEAR Страницы: 14

Бренд: dixell Страницы: 4

Бренд: Abocom Страницы: 2

Бренд: Keithley Страницы: 98

Бренд: Gbord Страницы: 8

Бренд: ICP DAS USA Страницы: 8

Бренд: Juniper Страницы: 7

Бренд: CyberTAN Страницы: 67

RP614 - Web Safe Router

Бренд: NETGEAR Страницы: 16

Бренд: TP-Link Страницы: 2

Бренд: TP-Link Страницы: 4

Бренд: AXIOMTEK Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды