Cisco UBR7246VXR Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 28

background image

3-3

Cisco Cable Clock Card Hardware Installation Guide for the Cisco uBR7246VXR Universal Broadband Router

OL-26705-01

Chapter 3 Removing and Installing the Clock Card

Clock Card Removal and Installation

Note

If the clock card installation screws do not appropriately assume a locked position, the clock card is not
completely seated in the midplane. Carefully pull the clock card halfway out of the slot, reinsert it, and
tighten the captive installation screws.

Caution

To prevent jamming the carrier between the upper and the lower edges of the clock card slot, and to
ensure that the edge connector at the rear of the clock card mates with the connection at the rear of the
clock card slot, make certain that the carrier is positioned correctly, as shown in the cutaway in the
following illustrations.

Warning

When performing the following procedures, wear a grounding wrist strap to avoid ESD damage to the
card. Some platforms have an ESD connector for attaching the wrist strap. Do not directly touch the
midplane or backplane with your hand or any metal tool, or you could shock yourself.

Warning

To reduce the risk of fire, use only No. 26 AWG or larger telecommunication line cord.

Clock Card Removal and Installation

In this section, the illustrations that follow give step-by-step instruction on how to remove and install the
clock card. This section contains the following illustrations:

•

Cisco uBR7246 VXR—Removing a Clock Card, page 3-4

•

Cisco uBR7246 VXR—Installing a Clock Card, page 3-5

«
...
17
18
19
20
21
...
»

Содержание UBR7246VXR





























Отзывы:

Нет отзывов

Похожие инструкции для UBR7246VXR

Mini Field Agent

Бренд: GE Страницы: 87

Бренд: Lattice Semiconductor Страницы: 15

Бренд: Quatech Страницы: 27

Бренд: Lindy Страницы: 4

Бренд: Delta Страницы: 2

Magic WiFi mini Ek

Бренд: Devolo Страницы: 22

NI WLS/ENET-9163

Бренд: National Instruments Страницы: 36

Бренд: peplink Страницы: 2

PCI-6110E/6111E

Бренд: National Instruments Страницы: 113

Net2Air Ins-40085-US

Бренд: Paxton Страницы: 4

Бренд: ZyXEL Communications Страницы: 215

Бренд: ZALMAN Страницы: 11

Easy Tool-ID BSG TID-05-T30-00-005

Бренд: Balluff Страницы: 46

memonizerWORKSTATION

Бренд: MEMON Страницы: 2

Бренд: Aethra Страницы: 2

Бренд: Crystal Vision Страницы: 54

Бренд: Supero Страницы: 16

EdgeRouter PoE ERPoe-5

Бренд: Ubiquiti Страницы: 13

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды