manualshive.com logo in svg

Cisco SCH-IO-EXT-8, Справочное руководство

Поделиться
Скачать
Cisco SCH-IO-EXT-8 Скачать руководство пользователя страница 10

 

10

Cisco Smart+Connected I/O Extender Reference Guide

OL-27368-01

  Resetting the Device

Resetting the Device 

Procedure

To reset the Cisco I/O Extender for system recovery, perform the following steps: 

Step 1

On the back of the device insert the end of a paper clip into the small hole (to the right of the Ethernet 
connector). 

Step 2

Power cycle the device by pressing and holding the Reset button for about 5-7 seconds and the Status LED 
blinks orange. This action starts the recovery process. 

Using the Identification Button 

  •

To reset the device to the network defaults, power cycle the Cisco I/O Extender (using the power 
button on the front of the device) and hold the Identification button until the Data, Link, and Power 
LEDs are solid blue; immediately release the button. 

  •

If during the boot sequence, the Status LED stays Orange, press and hold the Identification button 
until the LED blinks Blue, and then release it. 

Specifications

Table 1

Cisco I/O Extender Specifications 

Basic Specifications

Description

Status LEDs 

4 

Serial Ports (Male DB9 RS232) 

4 

IR Outputs 

8 

Contacts

8

Relays 8 

Network Connectivity 

10/100 BaseT Ethernet 

Power Supply 

100–240 VAC 

Amps

0.55 A 

Hertz

50–60 Hz 

Wattage

30W 

Dimensions (H x W x D)

1.59 in. × 16.84 in. × 6.34 in. 

 

(40.39 mm × 427.74 mm × 161.04 mm) 

Weight

4.8 lb. (2.18 kg) 

Power Cord

1 

IR Emitter Cables

6 

Rack Ears

Included 

Содержание SCH-IO-EXT-8















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды