Cisco RF Gateway 10 Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 58

background image

26

Release Notes for Cisco RF Gateway 10 in Cisco IOS Release 12.2SQ

OL-18677-10

Caveats

CSCud51870

Symptoms: Previous configurations of the line
card (prior to configuring redundancy) are still
preserved after the line card is removed from the
redundancy group. DEPI sessions are not cleared.

Conditions: This issue occurs when the primary
line card is removed from a redundancy group and
configured as a secondary in a new redundancy
group, and again removed from the new
redundancy group and added back into the
previous redundancy group as a primary line card.

Workaround: Before configuring any line card as
a secondary line card, default all QAM ports of
the line card to be configured as secondary. Issue
the default interface Qam command to default the
interfaces.

or

Manually remove all the configuration for that
line card.

CSCts77756

Symptom: Secondary sup ports are going to
admin down.

Conditions: During upgrade/Downgrade once
after all the LCs bootsup, do "sh ip int b | inc
admin" on slot 1. No ports will be in admin state
and Issue the "sh ip int b | inc admin" CLi in slot
2, all ports are in admin state. When I do SSO
using "red force switch", in newly active sup (slot
2) all ports still are shut.

Workaround: Change the ports to up state using

no shut

command.

CSCtz57400

Symptoms: DEPI sessions are not established on
the Cisco RFGW-10 when 4 sessions or its
multiples are not configured on the QAM
interface.

Conditions: This issue occurs when less than 4
sessions are configured.

Workaround: Configure DEPI sessions for all 4
channels on a QAM port.

CSCua42551

Symptoms: Front panel LEDs switch off after a
TCC card switchover.

Conditions: This issue occurs after the TCC card
switchover is performed.

Workaround: Reboot the Cisco RFGW-10 router.

Caveat

Description

«
...
24
25
26
27
28
...
»

Содержание RF Gateway 10



























































Отзывы:

Нет отзывов

Похожие инструкции для RF Gateway 10

UNIGATE CX C4Map

Бренд: DEUTSCHMANN AUTOMATION Страницы: 56

Бренд: Planet Страницы: 140

Бренд: Cisco Страницы: 10

Бренд: Cisco Страницы: 7

Бренд: Cisco Страницы: 19

Network Device MGX 8240

Бренд: Cisco Страницы: 2

Physical Access CIAC-GW-K9

Бренд: Cisco Страницы: 26

Бренд: Cisco Страницы: 60

Бренд: Cisco Страницы: 29

Бренд: Cisco Страницы: 94

Бренд: Cisco Страницы: 5

Бренд: Cisco Страницы: 10

Бренд: Cisco Страницы: 12

Бренд: Cisco Страницы: 22

Linksys WAG325N

Бренд: Cisco Страницы: 50

VG224 - Analog Phone Gateway

Бренд: Cisco Страницы: 20

Бренд: Cisco Страницы: 26

VG248 - Gateway

Бренд: Cisco Страницы: 130

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды