Cisco PWR-7513-AC Скачать руководство пользователя страница 1

Страница: 1 / 18

Doc. No.

Cisco Systems, Inc.

1200-Watt AC-Input Power Supply
Replacement Instructions

78-1900-02

Product Number: PWR-7513-AC(=), PWR-7513-ACU(=), PWR-7513-ACA(=),
PWR-7513-ACI(=), and PWR-7513-ACE(=)

This document contains instructions for installing or replacing a 1200-watt (W), alternating current
(AC)–input power supply in the Cisco 7513.

A single power supply is standard equipment for the Cisco 7513. A second, identical power supply,
when installed, provides redundant power.

In systems with redundant power, the power supplies are load-sharing and fully hot-swappable; you
can remove and replace one supply, while the remaining supply immediately ramps up to full power
to maintain uninterrupted system operation.

The sections in this document include the following:

•

Product Overview, page 2

•

Environmental Monitoring and Reporting Functions, page 5

•

Installation Safety, ESD Precautions, and Tools Required, page 10

•

Removing and Replacing a Power Supply, page 12

•

Checking the Installation, page 15

•

Cisco Information Online, page 17

Содержание PWR-7513-AC



















Результаты поиска

Содержание PWR-7513-AC

Отзывы:

Похожие инструкции для PWR-7513-AC

Бренды по названию

Популярные бренды

Cisco PWR-7513-AC, Инструкция по замене

Результаты поиска

Содержание PWR-7513-AC

Отзывы:

Похожие инструкции для PWR-7513-AC

Бренды по названию

Популярные бренды