Cisco o UCS X440p Скачать руководство пользователя страница 47 | Manualshive

Страница: 47 / 62

background image

Replacing the Rear Mezzanine Card

The UCS X440p PCIe node supports a rear mezzanine (MEZZ) card to provide data and power connectivity
to the PCIe node. The rear MEZZ socket is at the rear corner of the PCIe node.

To remove or install the rear mezzanine card, you will need to disconnect the front panel LED cable.
For the location of this cable, see

Serviceable Component Locations, on page 15

Note

To service the rear MEZZ card, use the following procedures:

•

Removing a Rear Mezzanine Card, on page 39

•

Installing a Rear Mezzanine Card, on page 40

Removing a Rear Mezzanine Card

Use the following task to remove the rear mezzanine card from the PCIe node.

Step 1

Shut down and remove power from the PCIe node.

Step 2

Remove the PCIe node from the chassis.

Step 3

Remove the top cover from the PCIe node.

See

Removing a PCIe Node Cover, on page 18

.

Step 4

Disconnect the front panel LED cable from the rear mezzanine connector.

You can leave the cable connected to the front panel connector, but make sure to move the cable out of the way so that
does not obstruct removing the rear mezzanine card.

Cisco UCS X440p PCIe Node Installation and Service Guide

39

Servicing the Cisco UCS X440p PCIe Node

Replacing the Rear Mezzanine Card

«
...
45
46
47
48
49
...
»

Содержание o UCS X440p































































Отзывы:

Нет отзывов

Похожие инструкции для o UCS X440p

BB-HGW700A - Network Camera Router

Бренд: Panasonic Страницы: 10

Бренд: iDirect Страницы: 60

Бренд: National Instruments Страницы: 26

Бренд: National Instruments Страницы: 85

Module SCXI-1503

Бренд: National Instruments Страницы: 79

Бренд: National Instruments Страницы: 28

Бренд: National Instruments Страницы: 19

Бренд: National Instruments Страницы: 36

Бренд: National Instruments Страницы: 103

NI PXI-1042 Series

Бренд: National Instruments Страницы: 12

Бренд: National Instruments Страницы: 4

Бренд: WAGO Страницы: 2

Бренд: Zenith Data Systems Страницы: 64

Brocade X6-8 Director

Бренд: Broadcom Страницы: 207

Бренд: Juniper Страницы: 190

Optane M Series

Бренд: Intel Страницы: 59

Бренд: DAD Страницы: 32

Бренд: LevelOne Страницы: 31

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды