background image

C H A P T E R

3

Installing the Chassis

Safety, on page 11

Installation Options with Rack-Mount Kits, on page 12

Airflow Considerations, on page 12

Installation Guidelines, on page 12

Unpacking and Inspecting the Switch, on page 14

Installing the Switch Using the NXK-ACC-KIT-1RU Rack-Mount Kit, on page 14

Grounding the Chassis, on page 18

Starting the Switch, on page 19

Safety

Before you install, operate, or service the switch, see the

Regulatory, Compliance, and Safety Information for

the Cisco Nexus 3000 and 9000 Series

for important Safety Information.

Statement 1071—

Warning Definition

IMPORTANT SAFETY INSTRUCTIONS

This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work
on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard
practices for preventing accidents. Use the statement number provided at the end of each warning to locate
its translation in the translated safety warnings that accompanied this device.

SAVE THESE INSTRUCTIONS

Warning

Cisco Nexus C9316D-GX ACI-Mode Switch Hardware Installation Guide

11

Содержание Nexus C9316D-GX





















































Отзывы: