manualshive.com logo in svg

Cisco Nexus 5500 Series NX-OS, Руководство по настройке

Конфигурационное руководство Cisco Nexus 5500 Series NX-OS доступно для загрузки бесплатно на manualshive.com. Этот manual поможет вам настроить и оптимизировать работу вашего устройства. Скачайте его уже сегодня, чтобы получить дополнительную информацию и решить любые проблемы с настройкой.

Поделиться
Скачать
background image

C H A P T E R  

7

Configuring SAN Port Channels

This chapter contains the following sections:

•

Configuring SAN Port Channels, page 93

Configuring SAN Port Channels

SAN port channels refer to the aggregation of multiple physical interfaces into one logical interface to provide
higher aggregated bandwidth, load balancing, and link redundancy.

On Cisco Nexus devices, SAN port channels can include physical Fibre Channel interfaces, but not virtual
Fibre Channel interfaces. A SAN port channel can include up to eight Fibre Channel interfaces.

Information About SAN Port Channels

About E and TE Port Channels

An E port channel refers to the aggregation of multiple E ports into one logical interface to provide higher
aggregated bandwidth, load balancing, and link redundancy. Port channel can connect to interfaces across
switching modules, so a failure of a switching module cannot bring down the port channel link. Cisco Nexus
devices support a maximum of four SAN port channels in FC switch mode, which includes E/TE-port port
channels.

A SAN port channel has the following functionality:

•

Provides a point-to-point connection over ISL (E ports) or EISL (TE ports). Multiple links can be
combined into a SAN port channel.

•

Increases the aggregate bandwidth on an ISL by distributing traffic among all functional links in the
channel.

•

Load balances across multiple links and maintains optimum bandwidth utilization. Load balancing is
based on the source ID, destination ID, and exchange ID (OX ID).

•

Provides high availability on an ISL. If one link fails, traffic previously carried on this link is switched
to the remaining links. If a link goes down in a SAN port channel, the upper layer protocol is not aware

Cisco Nexus 5500 Series NX-OS SAN Switching Configuration Guide, Release 7.x    

    OL-30895-01

93

Содержание Nexus 5500 Series NX-OS

































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Nexus 5500 Series NX-OS

Xantrex C12 Owner'S Manual preview
C12
Бренд: Xantrex Страницы: 8
Salusfin SF-930EU User'S Installation Manual preview
SF-930EU
Бренд: Salusfin Страницы: 6
Queclink GV600 Series Instruction Manual preview
GV600 Series
Бренд: Queclink Страницы: 9
Lanner NCA-1526 User Manual preview
NCA-1526
Бренд: Lanner Страницы: 78
Juniper ACX2000 Hardware Manual preview
ACX2000
Бренд: Juniper Страницы: 190
Paradyne Hotwire 6341 Installation Instructions Manual preview
Hotwire 6341
Бренд: Paradyne Страницы: 23
Draytek Vigor 2760 Series Quick Start Manual preview
Vigor 2760 Series
Бренд: Draytek Страницы: 54
Macsense MPC-200 User Manual preview
MPC-200
Бренд: Macsense Страницы: 13
ICP DAS USA USB-87P1 User Manual preview
USB-87P1
Бренд: ICP DAS USA Страницы: 62
ADTRAN NetVanta 873 Specifications preview
NetVanta 873
Бренд: ADTRAN Страницы: 2
Zhone 6388-A1-XXX Technical Specifications preview
6388-A1-XXX
Бренд: Zhone Страницы: 2
National Instruments NI 9229E Operating Instructions Manual preview
NI 9229E
Бренд: National Instruments Страницы: 26
TP-Link TD-W8101G Quick Installation Manual preview
TD-W8101G
Бренд: TP-Link Страницы: 16
ActionTec MI424WR MI424WR Upgrade Procedure preview
MI424WR
Бренд: ActionTec MI424WR Страницы: 3
Erbauer 3663602796282 Original Instructions Manual preview
3663602796282
Бренд: Erbauer Страницы: 36
TRENDnet TEW-752DRU User Manual preview
TEW-752DRU
Бренд: TRENDnet Страницы: 68
Patton electronics 1080ARC User Manual preview
1080ARC
Бренд: Patton electronics Страницы: 40
Foscam FN3104W User Manual preview
FN3104W
Бренд: Foscam Страницы: 92

Бренды по названию

Популярные бренды

Загрузить еще бренды