manualshive.com logo in svg

Cisco NCS 5700 Series, Руководство по установке оборудования

Поделиться
Скачать
Cisco NCS 5700 Series Скачать руководство пользователя страница 96

• AC power—The AC power supply has an IEC 320-type power receptacle and a 15 Amp service connector.

You can use standard right angle power cords with the AC power supply. The power supply includes a
power cord retainer. No ON/OFF switch is provided.

You can install dual power supplies for redundancy.

In low-line applications (90-140V AC), redundancy is not guaranteed. Therefore, we recommend to use both
AC and DC power supplies.

Caution

Products that have an AC power connection are required to have an external SPD provided as part of the
building installation to comply with the Telcordia GR-1089 NEBS standard for electromagnetic compatibility
and safety.

Note

Do not use interface module and power supply ejector handles to lift the chassis; using the handles to lift the
chassis can deform or damage the handles.

Caution

Remove the DC Power Supply Module

This section provides information about removing and replacing the DC power supply.

Before performing any of the following procedures, ensure that power is removed from the DC circuit.
Statement 1003

Warning

Only trained and qualified personnel should be allowed to install, replace, or service this equipment. Statement
1030

Warning

Follow these steps to remove and replace the DC power supply:

Step 1

Before servicing the power supply, switch off the circuit breaker in your equipment area. As an additional precaution,
tape the circuit-breaker switch in the Off position.

Step 2

Slip on the ESD-preventive wrist strap that was included in the accessory kit.

Step 3

Switch the power supply circuit-breaker switch to the Off (O) position.

Step 4

Pull the terminal block plug connector out of the terminal block head in the power supply. See the following figure.

Step 5

Grasp the power supply handle. Simultaneously press the power supply locking tab towards the left and pull the power
supply out from the chassis while supporting it with the other hand.

Hardware Installation Guide for Cisco NCS 5700 Series Fixed-Port Routers

90

Replace Chassis Components

Remove the DC Power Supply Module

Содержание NCS 5700 Series

























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды