Cisco NCS 5700 Series Скачать руководство пользователя страница 16

Страница: 16 / 120

MPA slots 2 and 3

MPA slot 1

Transceiver

Max bandwidth per MPA = 800GE

You can use a combination of
QDD-400GE (Port 0

Port 2) and

QSFP28-100GE/QDD-2x100GE (Port 0,
1, 2 or 3) transceivers at the same time,
provided the total bandwidth does not
exceed 800GE.

Note

Max bandwidth = 400GE

You can use a combination of
QDD-2x100GE (Port 0

Port 2) and

QSFP28-100GE (Port 0, 1, 2 or 3)
transceivers at the same time, provided
the total bandwidth does not exceed
400GE.

Note

All ports

QSFP28-100GE

All ports

Ports 0 and 2

When QDD-2x100GE transceivers are
installed in ports 0 and 2, ports 1 and 3
cannot be used.

Note

QDD-2x100GE

Ports 0 and 2

When QDD-400GE transceivers are
installed in ports 0 and 2, ports 1 and 3
cannot be used.

Note

Port 0

When QDD-400GE transceiver is
installed in port 0, ports 1, 2, and 3 cannot
be used

Note

QDD-400GE

Figure 6: NC57-MPA-2D4H-S Modular Port Adapter (MPA)

QSFP28/QSFP-DD port
and LED

STATUS LED

QSFP28/QSFP-DD port
and LED

ATTN LED

QSFP28/QSFP-DD port
and LED

Hardware Installation Guide for Cisco NCS 5700 Series Fixed-Port Routers

NCS 5700 Router Overview

Modular Port Adapters

Содержание NCS 5700 Series
























































































































Результаты поиска

Содержание NCS 5700 Series

Отзывы:

Бренды по названию

Популярные бренды

Cisco NCS 5700 Series, Руководство по установке оборудования

Результаты поиска

Содержание NCS 5700 Series

Отзывы:

Бренды по названию

Популярные бренды