Cisco NCS 5000 Series Скачать руководство пользователя страница 47 | Manualshive

Страница: 47 / 72

Cisco NCS 5000 Series Скачать руководство пользователя страница 47

Step 7

Verify that the power supply OK LED is green.

Replacing the Air Filter

A replaceable air filter is located on the front of the chassis. How often the air filters should be replaced
depends on the facility environment. In a dirty environment, or when you start getting frequent temperature
alarms, you should always check the intake grills for debris, and then check the air filters to see if they need
to be replaced.

In general, we recommend that you inspect the air filter every three months and replace, if necessary,
every 6 months.

Note

Procedure

Step 1

Remove the air filter that you are replacing as follows:

a) Loosen the captive screws that secure the fan filter. The air filter attaches to the front of the chassis for

port side inlet, in three parts (Piece A, Piece B and piece C as shown in the figure below). Remove piece
C first, followed by piece B and then piece A.

Figure 22: Replacing port side inlet air filter

Mid Panel (Piece C)

2

3x5 captive screws

1

Bottom Panel (Piece B)

4

4x4 captive screws

3

Unit Faceplate

6

Top Panel (Piece A)

5

Hardware Installation Guide for Cisco NCS 5000 Series Routers

39

Replacing NCS 5000 Router Components

Replacing the Air Filter

«
...
45
46
47
48
49
...
»

Содержание NCS 5000 Series









































































Отзывы:

Нет отзывов