manualshive.com logo in svg

Cisco NCS 5000 Series, Руководство по установке оборудования, Страница: 25 / 72

Поделиться
Скачать
Cisco NCS 5000 Series Скачать руководство пользователя страница 25

C H A P T E R  

4

Installing the NCS 5000 Router

This chapter describes how to install the Cisco NCS 5000 Series routers. This chapter includes the following
sections:

•

Installation Guidelines, page 17

•

Installing Cisco NCS 5000, page 18

•

Grounding Cisco NCS 5000, page 27

•

Starting Cisco NCS 5000, page 30

Installation Guidelines

When installing the Cisco NCS 5000 routers, follow these guidelines:

•

Ensure that there is adequate space around the router to allow for servicing the router and for adequate
airflow

Technical Specifications, on page 47

,lists the service and airflow requirements.

•

Ensure that the air-conditioning meets the heat dissipation requirements listed in

Technical Specifications,

on page 47

•

Ensure that the cabinet or rack meets the requirements listed in

Cabinet and Rack Installation , on page

45

Jumper power cords are available for use in a cabinet. See the

Jumper Power Cord, on

page 57

section.

Note

•

Ensure that the chassis can be adequately grounded. If the router is not mounted in a grounded rack, we
recommend connecting both the system ground on the chassis and the power supply ground directly to
an earth ground.

•

Ensure that the site power meets the power requirements listed in

Technical Specifications, on page

47

. If available, you can use an uninterruptible power supply (UPS) to protect against power failures.

•

Ensure that circuits are sized according to local and national codes. For North America, the power supply
requires a 15-A or 20-A circuit.

Hardware Installation Guide for Cisco NCS 5000 Series Routers    

17

Содержание NCS 5000 Series









































































Отзывы:

Нет отзывов