Cisco N9K-C9332C Скачать руководство пользователя страница 9

Страница: 9 / 70

C H A P T E R

Overview

•

Overview

The Cisco Nexus 9332C switch (N9K-C9332C) is a 1-RU, fixed-port switch designed for spine-leaf-APIC
deployment in data centers. This switch has 32 40/100-Gigabit QSFP28 ports and 2 SFP ports. Ports 25-32
offer hardware support for MACsec encryption.

To determine which transceivers, adapters, and cables this switch supports, see the

Cisco Transceiver Modules

Compatibility Information

document.

This switch includes the following user-replaceable components:

• Fan modules (five) with the following airflow choices:

• Port-side exhaust airflow with blue coloring (NXA-FAN-35CFM-PE)

• Port-side intake airflow with burgundy coloring (NXA-FAN-35CFM-PI)

Table 1: Fan Speeds for This Switch

Port-Side Exhaust

Fan Speed %

Port-Side Intake

Fan Speed %

70%

50%

Typical/Minimum

100%

Maximum

Note

• Power supply modules (two—One for operations and one for redundancy [1+1]) with the following

choices:

• 750-W AC power supply with port-side exhaust airflow (blue coloring) (NXA-PAC-750W-PE)

• 750-W AC power supply with port-side intake airflow (burgundy coloring) (NXA-PAC-750W-PI)

• 1100-W AC power supply with port-side exhaust airflow (blue coloring) (NXA-PAC-1100W-PE2)

Cisco Nexus 9332C ACI-Mode Switch Hardware Installation Guide

Содержание N9K-C9332C







































































Результаты поиска

Содержание N9K-C9332C

Отзывы:

Похожие инструкции для N9K-C9332C

Бренды по названию

Популярные бренды

Cisco N9K-C9332C, Руководство по установке оборудования

Результаты поиска

Содержание N9K-C9332C

Отзывы:

Похожие инструкции для N9K-C9332C

Бренды по названию

Популярные бренды