Cisco N9K-C9332C Скачать руководство пользователя страница 57 | Manualshive

Страница: 57 / 70

background image

Switch Power Input Requirements

The following table lists the typical amount of power that the switch consumes. It also lists the maximum
amount of power that you must provision for the switch and power supply for peak conditions.

Some power supplies have capabilities that are greater than the maximum power requirements for a switch.
To determine the power consumption characteristics for the switch, use the typical and maximum requirements
that are listed in the following table.

Note

Heat Dissipation
Requirement

Maximum Power
Consumption (AC or DC)

Typical Power
Consumption (AC or DC)

Switch

2415.796 BTUs per hour

708 W

296 W

Cisco Nexus 9332C

Power Specifications

Power specifications include the specifications for each type of power supply module.

750-W AC Power Supply Specifications

These specifications apply to the following power supplies:

• NXA-PAC-750W-PE

• NXA-PAC-750W-PI

Specification

Characteristic

750 W

Maximum output power

10 Amps at 100 VAC

Maximum input current

115 to 240 VAC nominal (Range: 90 to 264 VAC)

Rated input voltage

50 to 60 Hz nominal (Range: 47 to 63 Hz)

Rated input frequency

1100-W AC Power Supply Specifications

These specifications apply to the following power supplies:

• NXA-PAC-1100W-PE

• NXA-PAC-1100W-PI

Cisco Nexus 9332C ACI-Mode Switch Hardware Installation Guide

49

System Specifications

Switch Power Input Requirements

«
...
55
56
57
58
59
...
»

Содержание N9K-C9332C







































































Отзывы:

Нет отзывов

Похожие инструкции для N9K-C9332C

Бренд: FS Страницы: 23

Бренд: Black Box Страницы: 28

MediaHub Mini TA-3350

Бренд: TeleAdapt Страницы: 23

Бренд: Farallon Страницы: 22

Бренд: StarTech.com Страницы: 2

AVlink VAX-8404F

Бренд: C&C TECHNIC Страницы: 2

Бренд: Black Box Страницы: 50

SECURVIEW SV-7020

Бренд: CrimeStopper Страницы: 1

Бренд: Allen-Bradley Страницы: 4

Бренд: Comnet Страницы: 105

Бренд: GE Страницы: 26

Бренд: GE Страницы: 13

Бренд: GE Страницы: 12

Бренд: GE Страницы: 1

Бренд: GE Страницы: 2

Бренд: GE Страницы: 2

Бренд: GE Страницы: 36

Бренд: GE Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды