Cisco N9K-C9332C Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 70

background image

• The depth of a four-post rack must be 24 to 32 inches (61.0 to 81.3 cm) between the front and rear

mounting rails (for proper mounting of the bottom-support brackets or other mounting hardware).

• Required clearances between the chassis and the edges of its rack or the interior of its cabinet are as

follows:

• 4.5 inches (11.4 cm) between the front of the chassis and the interior of the cabinet (required for

cabling).

• 3.0 inches (7.6 cm) between the rear of the chassis and the interior of the cabinet (required for airflow

in the cabinet if used).

• No clearance is required between the chassis and the sides of the rack or cabinet (no side airflow).

Also, you must have power receptacles that are located within reach of the power cords that are used with the
switch.

Statement 1048—

Rack Stabilization

The rack stabilizing mechanism must be in place, or the rack must be bolted to the floor before installation
or servicing. Failure to stabilize the rack can cause bodily injury.

Warning

Clearance Requirements

Provide the chassis with adequate clearance between the chassis and any other rack, device, or structure so
that you can properly install the chassis. Provide the chassis with adequate clearance to route cables, provide
airflow, and maintain the switch. For the clearances required for an installation of this chassis in a four-post
rack, see the following figure.

Cisco Nexus 9332C ACI-Mode Switch Hardware Installation Guide

10

Preparing the Site

Clearance Requirements

«
...
16
17
18
19
20
...
»

Содержание N9K-C9332C







































































Отзывы:

Нет отзывов

Похожие инструкции для N9K-C9332C

Бренд: Camozzi Страницы: 2

Бренд: Valcom Страницы: 2

Бренд: Sams Страницы: 10

Бренд: Accton Technology Страницы: 547

IPES-5222T Series

Бренд: Lantech Страницы: 30

Бренд: cable matters Страницы: 8

Бренд: Lindy Страницы: 54

Бренд: Opengear Страницы: 109

Бренд: PTN Страницы: 44

Бренд: Kathrein Страницы: 41

enbrighten 51253

Бренд: Jasco Страницы: 2

IntraCore IC39240

Бренд: Asante Страницы: 3

Бренд: N-Tron Страницы: 2

Бренд: Angustos Страницы: 15

Бренд: SEKURYX Страницы: 13

Intraplex T1 DCS-9530 CrossConnect System

Бренд: GatesAir Страницы: 106

Бренд: IBM Страницы: 60

menber's Series

Бренд: Littelfuse Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды