Cisco MDS 9220i Скачать руководство пользователя страница 1

Страница: 1 / 20

Installing the Cisco MDS 9220i Switch

This chapter describes how to install the Cisco MDS 9220i switch and its components.

Before you install, operate, or service the system, see the

Regulatory Compliance and Safety Information for

document for important safety information.

This unit is intended for installation in restricted access areas. A restricted access area can be accessed
only through the use of a special tool, lock and key, or other means of security.

Statement 1017

Warning

Only trained and qualified personnel should be allowed to install, replace, or service this equipment.

Statement 1030

Warning

Each new switch requires a license. See the

Cisco MDS 9000 Series Licensing Guide, Release 8.x

for

instructions on installing a license.

•

Preinstallation, on page 1

•

Cisco MDS 9000 Series Telco and EIA Shelf Bracket, on page 2

•

Before Installing the Shelf Brackets, on page 2

•

Preinstallation Guidelines, on page 5

•

Installing the Switch, on page 7

•

Grounding the Switch, on page 16

•

Installing and Removing Power Supply Units, on page 17

•

Installing and Removing Fan Modules, on page 18

Preinstallation

This section includes the following information:

Installation Options

A Cisco MDS 9220i Switch can be installed using the following methods:

• In an open EIA rack

Installing the Cisco MDS 9220i Switch

Содержание MDS 9220i





















Результаты поиска

Содержание MDS 9220i

Отзывы:

Похожие инструкции для MDS 9220i

Бренды по названию

Популярные бренды

Cisco MDS 9220i, Руководство пользователя

Результаты поиска

Содержание MDS 9220i

Отзывы:

Похожие инструкции для MDS 9220i

Бренды по названию

Популярные бренды