background image

Configuring Cisco MC3810 Series Concentrators to Use High-Performance Compression Modules

codec (dial-peer)

9

Cisco IOS Release 12.1(2)T

Command History

Usage Guidelines

A codec type can be configured on the dial-peer if it is supported under the 

codec complexity

 setting 

you have specified. 

The dial-peer configuration command is particularly useful when you must change to a 
small-bandwidth codec. Large-bandwidth codecs, such as G.711, do not fit in a small-bandwidth link. 
However, 

g711alaw

 and 

g711ulaw

 provide higher-quality voice transmission than other codecs. For 

almost toll quality (and a significant savings in bandwidth), 

g729r8

 provides near-toll quality with 

considerable bandwidth savings. 

If the destination router does not support a codec required by the originating router, the call setup fails.

You can change the payload of each voice packet frame by using the 

bytes

 payload-size 

setting. However, 

increasing the payload size can add processing delay for each voice packet. Table 3 describes the voice 
payload options and default values for the codecs and packet voice protocols. 

Release

Modification

11.3(1)T

This command was introduced as a Cisco 3600 series VoIP dial-peer 
configuration command.

12.0(4)T

This command was modified for VoFR dial peers. On the 
Cisco MC3810 series, this command was first supported as a dial-peer 
command.

12.0(5)XK

The 

g729br8

 codec and 

pre-ietf

 keyword were added for the 

Cisco 2600 and 3600 series.

12.0(7)T

This command was implemented in the 12.0(7)T release.

12.0(7)XK

The 

g729abr8

 and 

g729ar8

 codecs were added for the Cisco MC3810 

series and the keyword 

pre-ietf

 was deleted.

12.1(2)T

This command was implemented in the 12.1(2)T release.

Table 3

Voice Payload-per-Frame Options and Defaults

Codec

Protocol

Voice Payload Options (bytes)

Default Voice 
Payload (bytes)

g711alaw
g711ulaw

VoIP
VoFR
VoATM

80, 160
40 to 240 in multiples of 40
40 to 240 in multiples of 40

160
240
240

g723ar53
g723r53

VoIP
VoFR
VoATM

20 to 220 in multiples of 20
20 to 240 in multiples of 20
20 to 240 in multiples of 20

20
20
20

g723ar63
g723r63

VoIP
VoFR
VoATM

24 to 216 in multiples of 24
24 to 240 in multiples of 24
24 to 240 in multiples of 24

24
24
24

g726r16

VoIP
VoFR
VoATM

20 to 220 in multiples of 20
10 to 240 in multiples of 10
10 to 240 in multiples of 10

40
60
60

g726r24

VoIP
VoFR
VoATM

30 to 210 in multiples of 30
15 to 240 in multiples of 15
30 to 240 in multiples of 15

60
90
90

Содержание Mc3810 - 16MB Flash Memory

















Отзывы: