Cisco IR8340 Скачать руководство пользователя страница 1

Страница: 1 / 10

Installing and Connecting the Router

This section describes how to install and connect the Cisco IR8340 router.

•

Installing and Connecting the Router, on page 1

•

Before You Begin, on page 3

•

Unpacking the Router, on page 4

•

Installing the Router in a Rack, on page 4

•

Replacing the SD Flash Memory Card, on page 7

•

Connecting the Console Port, on page 8

•

Connecting WAN and LAN Interfaces, on page 9

Installing and Connecting the Router

This section describes how to install and connect the Cisco IR8340 router.

For the optimum temperature ranges, do not operate it in an area that less than the minimum of -40°C
and exceeds a maximum recommended ambient temperature of 60°C.

Caution

To view specifications for the Cisco Catalyst IR8340 Rugged Series Router, see the IR8340 data sheet.

Note

Only trained and qualified personnel should be allowed to install, replace, or service this equipment.
Statement 1030

Warning

This unit might have more than one power supply connection. All connections must be removed to
de-energize the unit. Statement 1028

Warning

Installing and Connecting the Router

Содержание IR8340











Результаты поиска

Содержание IR8340

Отзывы:

Похожие инструкции для IR8340

Бренды по названию

Популярные бренды

Cisco IR8340, Установка и подключение

Результаты поиска

Содержание IR8340

Отзывы:

Похожие инструкции для IR8340

Бренды по названию

Популярные бренды