Cisco Expressway CE1000 Appliance Скачать руководство пользователя страница 15

Страница: 15 / 16

Notices

Technical support

If you cannot find the answer you need in the documentation, check the web site at

http://www.cisco.com/cisco/web/support/index.html

where you will be able to:

Make sure that you are running the most up-to-date software.

Get help from the Cisco Technical Support team.

Make sure you have the following information ready before raising a case:

Identifying information for your product, such as model number, firmware version, and software version
(where applicable).

Your contact email address or telephone number.

A full description of the problem.

To view a list of Cisco TelePresence products that are no longer being sold and might not be supported, visit:

http://www.cisco.com/en/US/products/prod_end_of_life.html

and scroll down to the TelePresence section.

Accessibility notice

Cisco is committed to designing and delivering accessible products and technologies.

The Voluntary Product Accessibility Template (VPAT) for Cisco Expressway is available here:

http://www.cisco.com/web/about/responsibility/accessibility/legal_regulatory/vpats.html#telepresence

You can find more information about accessibility here:

www.cisco.com/web/about/responsibility/accessibility/index.html

Cisco Expressway CE1000 Appliance Installation Guide (8.5)

Page 15 of 16

Notices

Содержание Expressway CE1000 Appliance

















Результаты поиска

Содержание Expressway CE1000 Appliance

Отзывы:

Похожие инструкции для Expressway CE1000 Appliance

Бренды по названию

Популярные бренды

Cisco Expressway CE1000 Appliance, Руководство по установке

Результаты поиска

Содержание Expressway CE1000 Appliance

Отзывы:

Похожие инструкции для Expressway CE1000 Appliance

Бренды по названию

Популярные бренды