Cisco CX-FEIP-1FX= Installation and con?guration Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 42

background image

Fast Ethernet Interface Processor (FEIP) Installation and Configuration 31

Configuring Interfaces—Descriptions and Examples

FE half-duplex operation is the default. To change to full-duplex operation, use the following series
of commands:

Router# configure terminal

Enter configuration commands, one per line. End with CNTL/Z.

Router(config)#

Router(config)# interface fastethernet 3/0/0

Router(config-if)# full-duplex

Ctrl-z

Note

Each 100BASE-TX or 100BASE-FX interface on an FEIP can be configured at 100 Mbps,

half duplex or full duplex, for a maximum aggregate bandwidth of 200 Mbps.

Caution

To prevent oversubscribing the FEIP, we recommend that you do not operate both FE interfaces on

an FEIP in full-duplex mode.

Using the show interfaces fastethernet command, you can see that the 3/0/0 interface is now
configured for full-duplex operation:

Router# sh int fa 3/0/0

FastEthernet 3/0/0 is administratively up, line protocol is up

(display text omitted)

Encapsulation ARPA, loopback not set, keepalive not set, fdx, 100BaseTX

To return the interface to half-duplex operation, use the no full-duplex configuration command as
follows:

Router# config t

Enter configuration commands, one per line. End with CNTL/Z.

Router(config)# int fa 3/0/0

Router(config-if)# no full-duplex

Ctrl-z

Router#

Using the show interfaces fastethernet command, you can see that the 3/0/0 interface is now
configured for half-duplex operation:

Router# sh int fa 3/0/0

FastEthernet3/0/0 is administratively up, line protocol is up

(display text omitted)

Encapsulation ARPA, loopback not set, keepalive not set, hdx, 100BaseTX

(display text omitted)

«
...
29
30
31
32
33
...
»

Содержание CX-FEIP-1FX= Installation and con?guration











































Отзывы:

Нет отзывов

Похожие инструкции для CX-FEIP-1FX= Installation and con?guration

Бренд: Aastra Страницы: 2

Бренд: Cambium Networks Страницы: 29

Module NI PXI-8250

Бренд: National Instruments Страницы: 39

Бренд: Patton electronics Страницы: 75

RocketLink-G 3088/I

Бренд: Patton electronics Страницы: 61

Бренд: Patton Страницы: 12

Бренд: Patton Страницы: 84

OnSite 3210 Series

Бренд: Patton Страницы: 110

Бренд: Patton electronics Страницы: 2

SMARTNODE 4110 Series

Бренд: Patton electronics Страницы: 78

Бренд: Patton electronics Страницы: 8

F-ZTAT H8/3048 Series

Бренд: Renesas Страницы: 34

INTERNET PRIVACY PROTECTION

Бренд: AlphaShield Страницы: 49

Бренд: IDT Страницы: 281

DMX-Universal-Demux

Бренд: DMX4ALL Страницы: 17

Бренд: Rockwell Automation Страницы: 108

Бренд: iBall Baton Страницы: 9

RUGGEDMAX WIN7000

Бренд: RuggedCom Страницы: 42

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды