Cisco CX-FEIP-1FX= Installation and con?guration Скачать руководство пользователя страница 1 | Manualshive

Страница: 1 / 42

background image

1

Customer Order Number:

Cisco Systems, Inc.
All rights reserved.

170 West Tasman Drive
San Jose, CA 95134-1706
USA

Cisco Systems, Inc.

Corporate Headquarters

Copyright © 1995–2002

Documentation Part Number:

Fast Ethernet Interface Processor (FEIP)
Installation and Configuration

Product Numbers: CX-FEIP-1TX=, CX-FEIP-2TX=, CX-FEIP-1FX=, CX-FEIP-2FX=

This configuration note is a standalone publication that provides instructions for installing and
configuring the Fast Ethernet Interface Processor (FEIP) in all Cisco 7000 series routers and
Cisco 7500 series routers. (For specific compatibility requirements, refer to the section “Software
and Hardware Prerequisites,” on page 3.)

Note

For convenience throughout this publication, FEIP-1TX, FEIP-2TX, FEIP-1FX, and

FEIP-2FX are referred to as FEIP, with specific differences clearly noted.

Included in this configuration note are steps for FEIP hardware installation and cable connection,
and basic FEIP configuration steps and examples. A table of contents is included so you can more
easily find what you need.

For additional descriptions of interface subcommands and configuration options available for Fast
Ethernet (FE) interfaces, refer to the appropriate Cisco IOS software configuration and command
reference publications listed in the section “If You Need More Information” on page 2.

DOC-781812=
78-1812-10

1
2
3
...
»

Содержание CX-FEIP-1FX= Installation and con?guration











































Отзывы:

Нет отзывов

Похожие инструкции для CX-FEIP-1FX= Installation and con?guration

Бренд: A-Link Страницы: 6

Бренд: Qualys Страницы: 2

SCSI PC Card REX-9530V

Бренд: Ratoc Systems Страницы: 30

Бренд: LORD Страницы: 9

ICS-G7748A Series

Бренд: Moxa Technologies Страницы: 10

Бренд: Zonet Страницы: 2

MultiConnect SE MTS2EA

Бренд: Multitech Страницы: 8

NJ220 - IntelliJack Switch

Бренд: 3Com Страницы: 82

Conel UR5i v2 Libratum

Бренд: B&B Electronics Страницы: 32

LinkStation Mini

Бренд: Buffalo Страницы: 71

COMMWARE ECHO 5G

Бренд: pivotal Страницы: 2

PowerBeam PBE-5AC-400-ISO

Бренд: Ubiquiti Страницы: 23

Бренд: ZALMAN Страницы: 9

Бренд: ivideon Страницы: 11

Mustang-M2AE-MX1

Бренд: IEI Technology Страницы: 58

24-Port 1000BASE-T

Бренд: Comet Labs Страницы: 44

Бренд: Cypress Semiconductor Страницы: 26

AirBridge VS-YOFIMN-000

Бренд: Vivint Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды