manualshive.com logo in svg

Cisco CPANM-1E1R2W, Конфигурационная записка

Поделиться
Скачать
Cisco CPANM-1E1R2W Скачать руководство пользователя страница 9

WAN Card Slot Network Module Configuration Note  9

Network Module Connectors

Figure 8

2E 2-Slot Network Module

1E1R 2-Slot Network Module

The 1E1R 2-slot network module has ports for one Ethernet connection and one Token Ring
connection. (See Figure 9.)

The Ethernet port (Ethernet 0) uses either the AUI (DB-15) connector or the 10BaseT (RJ-45)
connector, but only one at a time. The Token Ring port (Token Ring 0) uses either the shielded
twisted-pair (STP) connector or the unshielded twisted-pair (UTP) connector, but only one at a time.
Ports are identified in software by port type (Ethernet or Token Ring), the module’s slot number, and
the port number.

The module detects the type of network connection automatically, and you do not need to select the
media type in software. If cables are plugged into both Ethernet ports, the 10BaseT connection is
selected.

Figure 9

1E1R 2-Slot Network Module

2E
2W

W1

ETH 1

ETH 0

EN

WO

ACT

LNK

ACT

LNK

SERIAL

BRI
NT1

B1

B2

NT1

H6556

1E
1R

W1

STP

ETHERNET 0

AUI

EN

ACT

LNK

WO

TOKEN RING 0

16MBPS

IN-RING

Token Ring 

interface LEDs

10BaseT

port

STP port

UTP port

Ethernet

LEDs

AUI port

H6555

Key for BRI WAN
interface cards

Содержание CPANM-1E1R2W























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды