manualshive.com logo in svg

Cisco CPANM-1E1R2W, Конфигурационная записка

Поделиться
Скачать
Cisco CPANM-1E1R2W Скачать руководство пользователя страница 15

WAN Card Slot Network Module Configuration Note  15

Configuring the LAN Interfaces

Figure 17

2-Ethernet 2-WAN Card Slot Network Module

Figure 18

1-Ethernet 1-Token Ring 2-WAN Card Slot Network Module

Token Ring Module LEDs

The 1E1R 2-slot network module has two Token Ring LEDs, labeled 16MBPS and IN-RING. The
16MBPS LED indicates a ring speed of 16 Mbps. If it is off, the ring speed is 4 Mbps.

The IN-RING LED indicates that the Token Ring interface is inserted into the ring. If it is off, the
interface is not inserted into the ring.

Timesaver

When the IN-RING LED is off, you can unplug the Token Ring cable without causing

a problem on the ring.

Configuring the LAN Interfaces

Whenever you install a new interface, or if you want to change the configuration of an existing
interface, you must configure the interface. If you replace a module that was already configured, the
router recognizes it and brings up the interface in the existing configuration.

Before you configure an interface, have the following information available:

•

Protocols you plan to route on the new interface

•

IP addresses, subnet masks, network numbers, zones, or other information related to the routing
protocol

2E
2W

W1

STP

ETHERNET 0

ETHERNET 1

AUI

EN

ACT

LNK

WO

ACT

ILNK

LEDs

Key for BRI WAN
interface cards

10BaseT

port

10BaseT 

port

LEDs

Enable

LED

AUI port

H7213

1E
1R

W1

STP

ETHERNET 0

AUI

EN

ACT

LNK

WO

TOKEN RING 0

16MBPS

IN-RING

Token Ring 

interface LEDs

10BaseT

port

STP port

UTP port

Ethernet

LEDs

AUI port

H6555

Key for BRI WAN
interface cards

Содержание CPANM-1E1R2W























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды