background image

Stack ports must have the same speed capability on the module or cable plug in.

Note

The switch can only be stacked without Mesh topology. The switches in the same stack are connected together
through their stack ports. Depending on the type of stack ports and the desired speed, you may need Cat6a
Ethernet cables or Cisco approved modules or cables for the switches.

Stack Management

The Cisco Business switches have a couple of different stacking modes and you can stack different models.

Also you need to note what feature may of may not be available in different stacking modes (native or hybrid).

• Native Stacking - The switch is part of a stack in which all of the units are of the same type.

• Hybrid Stacking – The switch is part of a stack that can consist of either mixed types of CBS350 devices.

Feature Support on Hybrid Mode

The feature set of the CBS350 SKUs with 10G network ports and the feature CBS350 SKUs with 10G uplink
ports are nearly identical. However, there are a few differences in feature support and table sizes between the
2 “sub-types”. The Cisco Business switches hybrid stack mode will support the lower denominator for these
features/tables The following table lists the feature differences between the 2 sub-types and the setting applied
in hybrid mode:

Hybrid stack

CBS350 “10G network port
SKUs”

CBS350 “10G uplink port
SKUs”

Feature

Not Supported

Supported

Not Supported

OOB port

Per SKU and port type
behavior

Per SKU and port type
behavior

Per SKU and port type
behavior

Green Settings (Short
reach and Energy Detect)

16K

32K or 64K

16K

MAC table size

2K

4K

2K

Number of Multicast
groups

1K- reserved

2K- reserved

1K- reserved

Number of ACEs
supported

992

7392

992

Total number of IP entries

1K – reserved

8K – reserved

1K – reserved

ARP table size

106

200

106

Max number of IPv6
interfaces

400 seconds

630 seconds

400 seconds

Max MAC table aging

Not supported

Supported

Not supported

IPv6 Manual Tunnel/ 6tp4
tunnel/ ISATAP routing
tunnel

Get To Know Your Switch

6

Get To Know Your Switch

Feature Support on Hybrid Mode

Содержание CBS Series















Отзывы: