manualshive.com logo in svg

Cisco AVS 3120, Руководство по установке оборудования

Поделиться
Скачать
Cisco AVS 3120 Скачать руководство пользователя страница 10

 

3-10

Cisco AVS 3120 Application Velocity System Hardware Installation Guide

OL-11805-01

Chapter 3      Installing the AVS 3120

Configuring Network Settings

Configuring Network Settings

After you have installed the AVS 3120, you must configure the basic network settings by using the 

set

 

command in the CLI from a console connection. After the basic network settings have been configured, 
you can perform additional CLI configuration through the network by using an SSH connection. 
Additionally, you can configure application acceleration and other features by using the Management 
Console GUI in a Web browser. For details about using the CLI and Management Console, refer to the 

Cisco Application Velocity System User Guide.

To configure the basic network settings, follow these steps:

Step 1

Log in to the AVS 3120 from a console connected to the serial port.

Note

The default username is 

fgn

, and the password is 

fineground

.

After you log in, the 

velocity>

 prompt appears.

Step 2

Enable writing configuration settings with the 

enable

 command:

velocity>

enable

Step 3

Configure the network interface with the 

set interface

 command:

velocity>

set interface ip 

ip

 

netmask 

mask

 

default-gateway

 

gw

 

autoneg on

where:

ip

 is the device interface IP address, such as 10.210.10.45

mask

 is the device interface network mask, such as 255.255.255.0

gw

 is the gateway address, such as 10.210.2.1

autoneg

 can be set to 

on

 or 

off

, for speed autonegotiation (if off, you must set the speed and duplex 

settings manually by using the 

speed

 and 

duplex

 options)

You can view the interface settings by using the 

show interface

 command:

velocity>

show interface

PHYSICAL INTERFACE eth1

MAC ADDRESS: 00.0f.f7.75.75.73

Auto Negotiation: on

Duplex: full

Speed: 100

RX:  PKTS=1206954     BYTES=114173340     ERRORS=0

TX:  PKTS=428072     BYTES=53566339     ERRORS=0

MTU:         1500

INTERFACE NUMBERS

IP/NETMASK:  10.210.2.45/255.255.255.0

DEFAULT GATEWAY:  10.210.2.1

Step 4

Configure the DNS server addresses with the 

set dns

 command:

velocity>

set dns primary 

ip1

 

secondary 

ip2

where:

ip1

 is the primary DNS server IP address or name, such as 10.68.226.120

ip2

 is the secondary DNS server IP address name, such as 10.68.226.121

Содержание AVS 3120















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды